Bedienungsanleitung Whirlpool AWOC 9253 (Seite 3 von 12) (Englisch)

588993

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

GB 2

• The symbol on the product, or on the

documents accompanying the product, indicates

that this appliance may not be treated as

household waste. Instead it shall be handed over

to the applicable collection point for the recycling

of electrical and electronic equipment. Disposal

must be carried out in accordance with local

environmental regulations for waste disposal.

For more detailed information about treatment,

recovery and recycling of this product, please

contact your local city ofﬁce, your household waste

disposal service or the shop where you purchased

the product.

4. Frost

• Do not place the washing machine in a room

prone to frost. If you must, make sure that the

washingmachine is completely drained after each

wash:

• Remove inlet hose(s) from water tap and let the

water ﬂow out completely.

• Remove drain hose from siphon or handwash

basin and let the water ﬂow out completely.

• Empty residual water inside the machine by

following the instructions in the chapter “Draining

Residual Water”; for freestanding models: tilt the

appliance forward with two persons to let the rest

water ﬂow out completely.

5. EC Declaration of Conformity

• The appliance conforms to the following European

Standards: 2006/95/EC Low Voltage Directive

2004/108/EC Electromagnetic Compatibility

Directive.

The Manufacturer is not liable for any damage to

laundry resulting from inadequate or incorrect fabric

care instructions which have been provided with the

garment or article.

BEFORE USING THE WASHING MACHINE

1. Removing the packaging and

inspection

• After unpacking, make sure that the washing

machine is undamaged. If in doubt, do not use the

washing machine. Contact After-Sales Service or

your local retailer.

• Keep the packaging materials (plastic bags,

polystyrene parts, etc.) out of reach of children, as

they are potentially dangerous.

• If the appliance was exposed to the cold prior to

delivery, keep it at room temperature for a few

hours before operating.

2. Remove the transport bolts

• The washing machine is ﬁtted with transport

bolts to avoid any possible damage to the interior

during transport. Before using the machine, it is

imperative that the transport bolts are removed.

• After their removal, cover the openings with the 4

enclosed plastic caps.

3. Install the washing machine

• Remove the protective ﬁlm from the control panel

(if available on your model).

• Move the appliance without lifting it by the worktop.

• Install the appliance on a solid and level ﬂoor

surface, preferably in a corner of the room.

• Make sure that all four feet are stable and resting

on the ﬂoor and then check that the washing

machine is perfectly level (use a spirit level).

• In case of wooden or so-called “ﬂoating ﬂoors” (for

instance certain parquet or laminate ﬂoors), place

the appliance on a sheet of plywood at least 60 x

60 cm wide/deep and at least 3 cm thick which is

secured to the ﬂoor.

• Make sure that the ventilation openings in the

base of your washing machine (if available on your

model) are not obstructed by a carpet or other

material.

4. Water inlet

• Connect the water inlet hose(s) to the drinking

water supply in accordance with the regulations of

your local water company.

• For models with one inlet valve: cold water

• For models with two inlet valves: cold AND hot

water, or cold water only (see chapter “Installation

Guide”).

• Water tap: 3/4” threaded hose connector

• Water pressure (ﬂow pressure): 100-1000 kPa

(1-10 bar).

• Use only new hoses to connect the washing

machine to the water supply. Used hoses must not

be used and should be discarded.

• For models with hot ﬁll: the hot water inlet

temperature must not exceed 60°C.

5. Drain

• Firmly connect the drain hose to the siphon, or

another outlet for drain water.

• If the washing machine is connected to an

integrated drainage system, ensure the latter is

equipped with a vent to avoid simultaneous load-

ing and draining of water (siphoning effect).

6. Electrical connection

• Electrical connections must be carried out by a

qualiﬁed technician in compliance with the manu-

facturer’s instructions and current standard safety

regulations.

• Data regarding voltage, power consumption

andprotection requirements is given on the inside

of the door.

• The appliance must be connected to the mains

by means of a socket with an earth connection in

accordance with current regulations. The washing

machine must be earthed by law. The manufac-

turer declines all liability for damage to property

or injury to persons or animals due to non-compli-

ance with the directions given above.

• Do not use extension leads or multiple sockets.

• Access to the mains plug or disconnection from

the mains supply via a double-pole switch must be

ensured at all times after the installation.

• Do not operate the washing machine if it has been

damaged during transport. Inform the After-Sales

Service.

• Mains cable replacement is only to be carried out

by After-Sales Service.

• When using a residual current circuit breaker

(RCCB), only use a model marked with .

Whirlpool AWOC 9253 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool AWOC 9253

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info