Bedienungsanleitung Whirlpool AWT4123 (Seite 2 von 2) (Englisch)

586299

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

5019 312 10173

Whirlpool is a registered trademark of Whirlpool USA

Prewash cycle increases programme duration approximately 15 min. Consumption values were measured in normalized

conditions in compliance with standard IEC 60 456. Consumption data in the home may vary with respect to the values in

the table in relation to the water supply pressure and temperature, the load and the type of wash.

The data on the “Energy Label” refer to the programme “Cotton 60°C”.

* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the

water out.

1. Load the machine, close the drum doors and

check that they are properly locked.

2. Add detergents and additives into the dispenser

to no more then the “MAX” level mark, as

follows:

• Programme with pre and main wash

• Main wash programme without prewash

• Fabric softeners and conditioners

• Chlorine bleach

• Stain remover agents

• Anti-scale agents (if necessary)

3. Turn the programme selector knob to the

desired programme.

4. Turn the temperature selector knob to the

desired temperature.

5. Turn the spin speed selector knob to the

desired spin speed. If the spin speed “0” is

selected, the final spin is cancelled, but not the

intermediate spins. The programme ends with a

drain cycle.

Selecting or deselecting an option can be done at

any time during the programme. The option will

be applied as long as the corresponding

programme phase has not been executed yet.

“Intensive Rinse” button

• One rinse cycle is added to ensure a more

intensive rinse.

• This option is particularly suitable for areas with

very soft water, washing baby linen and people

with detergents allergies.

“Half Load” button

• Can be used for small loads and lightly soiled

laundry.

• Reduces the water consumption especially during

the rinses.

CONSUMPTION DATA

Programme Temperature Selector

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Approx. Programme

Duration

(hours : minutes)

Cotton 90 5.0 63* 1.80 2:05

Cotton 60 5.0 55 0.95 2:05

Cotton 40 5.0 55 0.55 2:05

Mixed Cotton/

Synthetic 60 2.0 46 0.80 1:35

Synthetic 40 1.5 52 0.40 0:55

Delicate 40 1.5 60 0.55 0:50

Wool 40 1.0 60 0.50 0:40

Handwash 30 1.0 60 0.30 0:50

PREPARATION OF WASH CYCLE SELECT THE DESIRED OPTION

“Rinse Hold” button

• The laundry remains in the last rinse water

without progressing to the final spin cycle to

avoid creasing and prevent colours from fading.

• This option is particularly recommended for the

“Synthetic” , “Delicate” programmes.

• This function is particularly useful if you want

to postpone spinning to a later time, or if you

want to drain only.

Note: the programme selector knob stops on .

Appliance in “Rinse Hold” :

• Press the “Rinse Hold” button again: the

programme will terminate automatically with

the selected spin cycle.

• If you do not wish to spin the clothes, press the

“On/Off” button , turn the programme

selector knob to the “Drain” programme

and press the “On/Off” button again.

Turn on the tap and press the “On/Off” button .

The indicator light of the “On/Off” button

lights up.

Note: If there is a power interruption or if the

appliance is disconnected during the cycle, the

programme will run again from the point where it

was interrupted.

• The programme selector knob is in the Stop

position.

1. Press the “On/Off” button to switch off the

machine.

2. Cancel the options.

3. Turn the tap off.

4. Wait for the lid to unlock (about 1 minute).

5. Open the lid and the drum doors and unload

the machine.

1. Switch off the machine by pressing the

“On/Off” button .

2. Select the new programme.

3. Start programme by pressing the “On/Off”

button again.

If, for any reason, you wish to interrupt the

programme for a certain time and continue it later:

1. Press the “On/Off” button .

2. After the desired pause, press again the

“On/Off” button .

1. Switch off the machine by pressing the

“On/Off” button .

2. Set the programme selector to “Drain” .

3. Press the “On/Off” button again to start

the “Drain” programme .

PROGRAMME START

END OF WASH CYCLE

CHANGE THE PROGRAMME DURING THE WASH

CYCLE

PAUSE/INTERRUPT A PROGRAMME

CANCEL PROGRAMME

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool AWT4123 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool AWT4123

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info