5019 301 06142
Whirlpool is a registered trademark of Whirlpool USA
Add detergent as indicated on the front page and as
described in the chapter “Detergent and Additives”
in your Instructions for Use.
1. Turn the
programme selector
to the desired
programme and temperature.
2. The
time display
shows the duration of the
chosen programme (in hours and minutes), and
the “Start/Pause” indication lamp is flashing.
3. The
indication lamp
of the predefined spin
speed lights up.
Push the button(s) of any option(s) desired - the
respective indication lights up.
When the combination of programme and additional
option(s) is not possible, the indication lights switch off
automatically. Unsuitable combinations of options are
deselected automatically.
“Eco” button
• With a modified temperatu re profile and a slightly
prolonged washing duration, the optimum
combination of excellent washing result and even
lower energy consumption can be achieved.
“Prewash” button
• Only for heavily soiled loads (for example sand,
granular dirt) sensible. Increases the cycle time
by approximately 15 min.
“Easy ironing” button
• Can be used together with “Cotton ”,
“Synthetics” and “Daily load” programmes to
make ironing easier .
• Increases the water quantity and the clothes are
spun very gently .
“Intensive rinse” button
• More water is added and rinse cycle is prolonged.
• This option is particularly suitable for areas with
very soft water , washing baby linen and helps
people with allergies.
“Rinse hold” button
• The laundry remains in the last rins e water
without progressing to the final spin cycle to avoid
creasing and prevent colours from changing.
• This option is particularly recommended for the
programmes “Synthetics”, “Daily load” and “Delicates”.
• It is particularly useful if you want to postpone
spinning to a later time, or if you want to drain only .
Note:
The programme stops to “Rinse hold” at
the time the “Rinse hold” light in the programme
sequence indication is on. The in dication lamp
next to the
“Start/P ause”
button flashes.
T erminate the “Rinse hold” option:
•P r e s s t h e
“Start/Pause”
button; the
programme will terminate automatically with the
final spin cycle for the present wash programme.
•I f y o u d o n o t w i s h t o s pin the clothes, turn the
programme selector knob to the “Drain ”
programme and press the
“Start/P ause”
button.
“ V ariable spin” button
• Every programme has a predefined spin speed.
• P ress the button to set another spin speed.
• If spin speed “0” is selected, the final spin ning is
cancelled but intermediate spin peaks remain
during rinse. The water is dra ined out only .
CONSUMPTION DATA
Pro g ra m me
T emperature
(°C)
Load
(kg)
Wa t e r
(l)
Energy
(kWh)
Approx. Programme Duration
(hours : minutes)
*
Cotton / Antibacterial 95 7.0 74
**
2.10 2:10
Cotton with “Eco”
***
60 7.0 69 1.33 2:20
Cotton 40 7.0 69 0.75 2:05
Synthetics 60 3.0 46
**
0.80 1:35
Synthetics 40 3.0 42 0.40 1:20
Delicates 30 1.5 60 0.50 0:45
Daily load 40 4.0 48 0.50 1:00
Quick wash 30 4.0 48 0.25 0:30
W ool 40 1.0 60 0.55 0:45
Handwash 40 1.0 45 0.55 0:40
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the hom e
may vary with resp ect to the values in the table in relation to the water supply pre ssure and temperature, the load and the type of wash.
*
The remaining time indicator can deviate from the values in the table, because it takes into account the household
conditions
applicable at that time.
**
T o reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water o ut.
***
Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTIO N
The “Start Delay” allows to run the machine at the
consumer’s convenience, for example at night when
electricity is cheaper.
• Select programme, temperature and options.
• P ress the “Start Delay ” button to select the
delay time by 1 to 23 hours;
•P r e s s t h e
“Start/P ause”
button.
The indication light next to the “Start Delay ”
button lights up and the countdown of the delay
time begins.
•T h e t i m e d e l a y i n d i c a t ion disappears when the
programme starts and it is replaced by the
remaining programme time.
• Once having pressed the
“Start/P ause”
button,
the number of hours preselected can be reduced
by pressing again the “Start Delay ” button.
T o cancel the “Start Delay ”
..before you press the “Start/P ause” button:
• T urn the programme selector to another
position or press the
“Reset”
button.
..after having pressed the “Start/P ause” button:
• Press the
“Reset”
button for at least 3 seconds - the
start delay time disappears from the time display .
Open the tap and press the
“Start/P ause”
button.
The indication lamp next to the
“Start/P ause”
button lights up. The programme sequence indicator
shows the current programme phase, running from
left to right through Wash, Rinse, Spin/Drain.
The time display shows the remaining programme
time. Due to variations in load and temperature of
inlet water, the remaining time is new ly calculated in
certain programme phases. If this is the case, an
animation appears on the time display.
Before starting and after end of a programme, the
lamp lights to show that the door can be opened. As
long as a wash programme is running, the door
remains locked and must on no account be forced
open. In case you have an urgent need to open it
during a running prog ramme, refer to “Cancel
(Reset) a running programme before the end”.
“Service”
Lighting up of the “Service” indication can be caused by
a fault in an electrical component. Refer to the
“Troubleshooting Guide” in your Instructions for Use; if
the fault persists, contact our After Sales Service.
“Water tap closed”
The appliance has no or insufficient water supply.
Open the water tap; if the indication still lights up,
refer to the “Troubleshooting Guide ” in the
Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the
drain hose is kinked or the filter must be cleaned; in
the latter case refer to the Instructions for Use
(“Removing the Filter”).
• All the lights of the programme sequence indicator
are off , and the “Door open ” indication lights up.
1. Turn the programme selector to the “Off/O”
position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
1. Press the
“Start/P ause”
button to pause the
programme. The light flashes.
2. Select the new programme (with temperature),
any options and another spin spee d if you want.
3 . Press the
“Start/P ause”
button again. The new
programme continues at the same position where
the previous programme was interrupted. Do not
add detergent for this programme.
The
“Reset”
button cancels a programme before
the end.
•P r e s s t h e
“Reset”
button for at least 3
seconds. Any existing water is drained out
before the door can be opened.
START DELAY
PROGRAMME START
“DOOR OPEN” INDICATION
RED INDICA TIONS
PROGRAMME END
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
30106142GB.fm Page 2 Wednesday, January 16, 2008 5:49 PM
Black process 45.0° 100.0 LPI