650640
3
Zoom out
Zoom in
Vorherige Seite
1/8
Nächste Seite
3
EN
Turn the knob to select the desired drying time. Conrm it
by pressing the knob.
Set dryness level, if needed
If you want to change the dryness level, make sure that the
Dryness level button « lights up.
Turn the knob to select the desired dryness level, then press
the knob to conrm.
Select options, if needed
If you want to select additional options, make sure that the
Options button « lights up. The options which are selectable
for your programme are indicated by lighting arrows.
Turn the knob to select the desired options. The symbol of
the selected option will blink. To conrm it, press the knob.
Some options / functions can be selected by directly
pressing the button.
Refer to section OPTIONS, FUNCTIONS AND
INDICATORS for more information.
INDIVIDUAL MODE
After you have switched on the dryer, you are not forced to
follow the GUIDED MODE.
It is up to you which order you choose to set your
programme. To do a setting, rst press the relevant button,
then turn the knob to select, and nally press the knob to
conrm.
The variety of options and dryness levels depends on the
programme selected. Therefore it is recommended to start
your setting with selecting the programme.
5. START PROGRAMME
Press and hold Start/Pause « until the button lights up
solidly; the drying process starts.
The duration can be recalculated and adapted in the course
of the programme.
During such phases, an animation occurs on the display.
6. CHANGE THE SETTINGS OF A RUNNING
PROGRAMME, IF NEEDED
You can still change some settings after a programme was
started:
• Adjust drying time (only if programme Drying time is
selected)
• Add or cancel an option, provided the progress of the
programme still allows it.
Press the relevant button. The selected setting will blink for
a few seconds.
While blinking, you can adjust the setting by turning the
knob. If the value or setting stopped blinking, press the
button again.
Press the knob to conrm the modication. If you do not
conrm, the modication will be conrmed automatically
— the modied setting will stop blinking.
The programme will continue automatically.
To change the settings of a running programme or start
delay, you can also:
• press Start/Pause to put the running programme on pause
• change your settings
• press Start/Pause again to continue the programme.
7. RESET A RUNNING PROGRAMME, IF NEEDED
Press and hold the On/O button « until “rES” appears on
the display.
The programme is ended afterwards.
Immediately open the door and unload the laundry, so that
eventual heat in the laundry can dissipate.
8. SWITCH OFF THE DRYER AFTER PROGRAMME END
At the end of the programme, „End“ appears on the
display. Press On/O « to switch o the dryer. Open the
door and take out your laundry.
The dryer will switch o automatically in about a quarter of
an hour after programme end, to save energy.
9. EMPTY WATER TANK / CLEAN DOOR FILTER /
CLEAN BOTTOM FILTER
Refer to section CARE AND MAINTENANCE.
3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Whirlpool HSCX 10443 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Whirlpool HSCX 10443

Whirlpool HSCX 10443 Bedienungsanleitung und Installationsanweisung - Englisch - 43 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info