CHILD L
Y
children). Pr
for at least 3 seconds on the display lights up
unlock the buttons again proceed in the same wa
BLEA
W or Synthetics ,
adding an appropriate amount of chlorine bleach to the Softener chamber
(close the lid carefully). Immediately after the end of the programme
“Prog
any residual bleach smell; if yNever put both
chlorine bleach and softener into the softener chamber at the same time.
HINTS AND TIPS
Sort your laundr
T
items). Colour (separat
separately). Delicates (wash small it
with hooks – like bras – in a cloth bag or pillow case with zip).
Empty all pockets
Objects like coins or lighters can damage your laundry as well as the drum.
Appliance interior
If you never or seldom wash your laundry at 95°C, we recommend t
occasionally run a 95°C programme without laundry
of detergent, to keep the in
Follo
It optimizes the cleaning result, it avoids irritating residues of surplus
detergent in your laundry and it saves money by a
detergent
Use low temper
The most efficient progr
those that perform at lower temperatures and longer dur
Observe the load sizes
Load your washing machine up t
CHART
Noise and remaining moisture c
They are influenced b
in the spinning phase, the higher the noise and the lower the r
moisture conten
CLEANING &
For an
machine. Do not use flammable fluids to clean the washing machine
and maintain your washing machine periodically (at least 4 times per year).
Cleaning the outside of the washing machine
Use a soft damp cloth to clean the outer parts of the washing machine. Do
not use glass or general purpose cleaners, scouring pow
the control panel – these substances migh
Detergent dispenser
Clean regularly
up:
Press the r
to r
A small quantity of water can remain in the dispenser
in an upright position.
remove the siphon cap on the back of the
dispenser for cleaning. Replac
Reinstall the dispenser by locating the dispenser’
appropriate openings on the lid, and b
lid until it locks into placeMake sure that the det
reinstalled.
Checking the water supply hose
Check the inlet hose regularly for brittleness and cracks
it by a new hose available through our A
dealer
coating, periodically check if the colour in
may have a leak and should be r (If
available): check the small safety valv
red, the wat
by a new one. F
while unscrewing the hose.
Cleaning the mesh filters in the water supply hose
Check and clean regularly (at least two or three times a year).
Close the tap and loosen the inlet hose on the tap. Clean the int
filter and screw the wat
hose on the rear of the washing machine. P
washing machine connection with universal pliers and clean it. Refit the mesh
filter and screw the inlet hose on again.
connections are completely water
Cleaning the water filter / dr
The washing machine is pro
objects like buttons
If you used a hot wash progr
before draining any w
water c
cannot drain, the indic
Open the filter cover with a c
water filter
until water flow
When the container is full, close the wa
Empty the container
a cotton cloth beneath the wat
rest water
the water filter (r
and the filter chamber
the filter) is not obstructed. Insert the water filter and close the filter cover:
Reinsert the water filter again by turning it in clockwise direction. Make sure
to turn it in as far as it goes.
pour about 1 liter of water int
from the filter
Lid seal
Check the condition of the lid seal periodically and clean it from time to time
with a damp cloth.
Recov
If an object accidentally falls between the drum and the tub, you can r
it thanks to one of the removable drum lifters
Unplug the washing machine. Remove the laundry from the drum. Close the
drum flaps and turn the drum a half-turn (picture a ). Using a screw-driver
press on the plastic end, while sliding the lifter from left to right (picture b , c)
by hand it will fall into the drum. Open the drum.
through the hole in the drum. Refit the lifter from inside the drum: P
the plastic tip above the hole on the right side of the drum (picture d ). T
slide the plastic lifter from right to left until it clips. Close the drum flaps again,
turn the drum through half a turn and check the positioning of the blade at all
its anchorage points. Plug the washing machine in again.
TRANSPORT AND HANDLING
Pull out the mains plug
from the water tap
Remove all rest wa
so that they cannot get damaged during transport. T
machine, pull the mobility lever situated at the bott
your model) out a little by hand. P
with the foot. Afterwards push the mobility lever back into the original stable
position. Refit the transport bracket. Follow the instructions for r
transport bracket in the INST
ab c d
EN
Quick guide
