Bedienungsanleitung White Knight WM126M (Seite 10 von 12) (Englisch)

484212

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

P.19P.18

Remove the plug before accessing the drain pump.

The water in the pump may be hot, allow the machine to cool before removing the pump cover.

The drain pump filter prevents foreign objects from entering the drain pump.

The filter should be cleaned periodically to ensure the normal operation of the appliance.

If heavily soiled items are washed regularly then the filter will need cleaning more often.

The pump filter should be inspected if the machine does not empty and/or spin.

If the machine makes an unusual noise whilst draining, there may be foreign objects in the pump.

To remove the objects:

Cleaning the Drain Pump Filter

1.Disconnect the appliance.

2.If necessary, wait until the water has cooled down.

3.Open the Service Panel.

4.Place a shallow container under the outlet.

5.Slowly turn the Pump Cover anti-clockwise. Collect the water that is released.

6.When no more water comes out, remove the Pump Cover.

7.Remove any objects from the pump and check that the impeller rotates.

8.Replace the Pump Cover and fully tighten it clockwise.

9.Close the Service Panel.

Unscrew the pump cover Close the service panel

Open the service panel

Screw the pump cover

MaintenanceMaintenance

Gently pull the detergent drawer forwards and then:

1.Press down the arrow located on the conditioner

compartment cover and remove the drawer from

the appliance.

2.Lift the clip up and remove the conditioner compartment

cover.

3.Thoroughly wash all the compartments and grooves

with warm water.

4.Replace the conditioner compartment cover.

5.Slide the detergent drawer back into the appliance.

The water inlet filters should be cleaned if there is

not any or insufficient water entering the machine

when the water tap is open.

1.Close the water tap.

2.Select a wash program.

3.Press the “Start/Pause” button and allow the machine to

run for about 40 seconds.

4.Remove the inlet pipe from the tap.

5.Clean the filter, in the end of the inlet pipe, with water.

6.Reconnect the inlet pipe.

1.Remove the inlet pipe from the rear of the appliance.

2.Pull out the filter from the appliance inlet, with a pair of long

nosed pliers.

3.Clean the filter and replace it into the inlet.

4.Reconnect the inlet pipe.

5.Open the water tap and check that there is no water leakage.

6.Close the water tap.

Note: The tap filter should be cleaned first.

Cleaning the Water Inlet Filters

Cleaning the Tap Filter:

Cleaning the appliance inlet filter:

Cleaning the Detergent Drawer

When the appliance is in use and depending on the program selected,

there could be hot water in the pump. Never remove the Pump Cover during a wash cycle,

always wait until the appliance has finished the cycle and is empty.

When replacing the Pump Cover ensure that it is securely tightened to prevent any leaks.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

White Knight WM126M Seite 10

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info