643499
20
Zoom out
Zoom in
Vorherige Seite
1/22
Nächste Seite
20 | P a g e
TROUBLESHOOTING
Problem Possible Causes Solutions
The portable air
conditioner does not
turn on
Power failure / outage.
The automatic switch, line
fuse, or breaker has been
tripped
The power supply voltage is
too low
The power cord is damaged
The L.C.D.I. power plug for
the unit is tripped
The internal water reservoir is
full and ‘P1” appears on
display
Restore the power supply
Flip the switch / change the fuse / turn the
breaker back on. Also note that you may
have too many appliances drawing power on
one circuit, you may need to move the other
appliances to another circuit
Move the unit onto another circuit with the
correct voltage
Call for service. Only authorized personnel
should replace damaged power cord or
power plug
Press the Reset button on the L.C.D.I. power
plug
Drain water from the air conditioner
Possible loose internal connection. Please
contact Whynter for service
The unit turns on but
the compressor does
not turn on (the fan runs
but the unit is not
cooling)
The room temperature is
outside of the operational
tolerances of the unit
The Cooling mode is not on
The compressor has not
turned on yet because of its
time delay
The set temperature is too
high
The internal water reservoir is
full and ‘P1” appears on
display
This unit is designed to work in ambient
temperatures of 63°F to 90°F
Press the MODE button until the COOL light
is shown on the display
Give the compressor 3 minutes to turn on
after the Cooling mode has been selected
Set the air conditioner to a lower
temperature. It is recommended to set the
temperature to at least 5°F of the ambient
temperature
Either manually drain the water by removing
the drain plug or allow the unit to exhaust the
water itself by running the fan only mode.
Then cooling will resume
Possible loose internal connection. Please
contact Whynter for service
The air coming out of
the unit is not very cold,
or the airflow volume is
weak
The filters are dirty or
obstructed
The air intake or exhaust is
obstructed
The unit is set in DRY or FAN
mode
The unit is set to low fan
speed
Clean the air filters
Make sure there is at least 20" of clearance
from the air intake. Make the length of the
exhaust hose is as short as possible
Set the unit to the cooling mode
Set the unit to a higher fan speed
20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Whynter ARC-142BX wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info