Bedienungsanleitung Wiking Scandic (Seite 26 von 40) (Deutsch, Englisch)

745719

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

Be Careful of the Lacquer

The lacquer used to treat the wood-burning stove will harden the rst 2-3 times the stove is red, and

this can create unpleasant smoke and odours. Ensure therefore that the room is well ventilated. The door

must also be carefully opened; otherwise there is a risk that the seals will stick to the lacquer.

Warning: The enclosed gloves can scratch the surface paint if the lacquer has not hardened properly. Be

careful not to touch the lacquered surfaces until after the rst 2-3 rings.

Lighting

1. Both the primary and secondary dampers are pushed as far to the right as possible. This

completely opens up both primary and secondary air.

2. Stack 8-10 nely split pieces of rewood, corresponding to 1-2 kg, inside the wood-burning

stove. The smaller the sticks, the shorter the time needed for the stove to be heated and for the

optimal combustion temperature to be achieved.

3. Place two relighters between the top layer of kindling. WIKING recommends using high-quality

relighters, as they do not produce smoke or odours.

4. Light the relighters. Keep the door ajar for a couple of minutes until the glass is hot - this pre-

vents condensation. Then close the door completely.

5. When the rewood is burning well, push the primary damper all the way to the left while slightly

adjusting the secondary damper to get an even and steady combustion.

Warning: The door may only be kept open when lighting, adding rewood or cleaning the wood-burning

stove; otherwise combustion becomes too powerful, which in turn increases the risk of the stove be-

coming overheated.

Firing (adding rewood)

When there are no more visible ames and only a solid layer of embers remains, more fuel can be added

to the re.

1. Carefully open the door to prevent smoke and embers from escaping.

2. Lay 2-4 pieces of split rewood (approximately 2 kg) on top of the embers.

3. Close the door and completely open the primary and secondary dampers by pushing them to

the right.

4. After a short while the ames should are up again. When the rewood is fully ignited, push the

primary damper to the left again while slightly adjusting the secondary damper, until the ames

burn evenly and steadily.

Warning: During combustion, the stove’s surfaces and door become extremely hot - exercise great

caution.

Some Things Worth Knowing about the Smoke Pipe

Description of the Smoke Pipe’s Function

The smoke pipe is the duct located between your wood-burning stove and chimney. All WIKING wood-

burning stoves are equipped with an exhaust pipe 150 mm in diameter.

If your stove is to be connected to a brick chimney, it is best to mount a curved smoke pipe to the stove’s

top outlet. Opting for this solution - in which the smoke pipe extends a half meter over the stove before

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wiking Scandic Seite 26

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Wiking Scandic

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info