Bedienungsanleitung WLtoys V252 SKYLARK (Seite 6 von 8) (Englisch)

608993

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

Calibration

Troubleshooting

- Do not use the copter when it has visible or mechanical damage.

- Always stay out of reach of rotors.

- Ensure that you adhere to all the legal requirements that exist for your copter model in the country in which you are using it.

If the copter is unstable, resulting in frenetic flying in all directions, and rotates around its axis so that you have to constantly

correct its flight, then the gyroscope is probably not calibrated properly. To perform recalibration, connect the drone to the

transmitter (part Activation in the manual), then click on 100% button of the remote and move both sticks to the bottom left. When

the calibration is performed, you will either hear a long beep or see flashing lights (on the PCB) or both.

Note: The calibration is done in the factory, it is usually not necessary to do it when you receive the product.

- Always use a fully charged battery.

1. For your first flight make sure to be with a person experienced in flying copters. We advise you to make your first flights on a

relatively soft surface to protect the copter.

2. Find a location away from people, with a smooth surface and without obstacles. Trees, electric lines and water points in the

immediate vicinity should be avoided!

3. Place your copter on the ground about 10 feet away from you. Mind that, when you have a quadcopter, the coloured blades

indicate the front of the copter. It is easiest to position yourself behind the copter for an easier control.

4. Turn the copter on first. Then turn on the remote controll (for some models this will be the other way around) for the V333N,

turn on the copter as well as the controller. then move trottle up and down to connect. after this move throttle to the left low corner

and the directional lever to the right lower corner at the same time, hold these down for a few seconds, this will arm the motors.

5. Start the engine and take off to about 1 meter from the ground. In this way you avoid the phenomenon called "ground effect".

Near the ground the air currents behave differently than at a higher altitude and this will prevent you from losing control of the

copter.

6. Then try to fly gently in one direction. If the engine flies away in the wrong direction, make a controlled landing and try again.

- Remember to disconnect the battery of the copter after each flight.

- If you lose control of the copter, disable the propulsion of the engines immediately by pushing the throttle lever down to turn it off.

- Always fly in an open and Jellyfished environment to avoid dangerous situations.

1. The receiver LED blinks continuously for more than 4 seconds after the quadcopter battery have been inserted. No response to

the command input. The transmitter is not connected to the device. Repeat the power-on initialization process.

2. No response from the quadcopter after the battery have been connected. There is probably contact failure on the battery

terminals. Turn on the transmitter and ensure that the battery of the vehicle is correctly inserted. Replace the battery and ensure

good contact at the battery's connections. Use fully charged batteries in the remote.

3. The motor does not respond to the throttle stick and the receiver flashes. The quadcopter's battery is exhausted. Charge the

battery or replace it with a charged battery.

4. The main rotor continues to rotate after landing. Confirm that the gear lever is oriented downward.

5. The main rotor rotates but the device does not take off. The blades may be distorted or the quadcopter battery is exhausted.

Charge or replace with a fully charged battery and / or replace the blades.

6. The quadcopter suffers of strong vibrations. The blades are distorted. Replace the blades.

7. The tail is not balanced after adjusting the clip or speed is inconsistent in the left / right pirouette. Tail rotors are probably

damaged. Replace the main wing and / or the main engine.

8. The quadcopter was still moving forward after the adjustment of the levers during hover. The gyroscope is not correctly

calibrated. The gear lever is placed too high or too low. The boot refines the calibration therefore restart on a flat surface.

9. You can not fly, the helicopter falls. The motor is probably fall out or the gears are loose. Reinstall the motor and tighten the

gears.

- Ensure that the copter in flight is always within sight and under control.

CAUTION

- When finished flying, always turn off the copter first, then the remote control.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

WLtoys V252 SKYLARK Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von WLtoys V252 SKYLARK

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info