Bedienungsanleitung WOLF-Garten SDE 2800 EVO (Seite 13 von 98) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

523453

Zoom out

Zoom in

Vorherige Seite

1/98

Nächste Seite

Changing blades

Remove the mains plug before any maintenance and

cleaning work!

When servicing the cutting tool ensure that it can still al-

ways run on even when the motor is switched off.

For safety reasons, always have the blades changed by an

authorised service centre.

1. Unscrew the knob and fold the casing upwards to open .

2. In order to change the blades insert the hexagon spanner (1)

in the slot on the retaining plate and through the cover.

3. Loosen the two screws with the Allen spanner

(2) and take

out the worn blades.

4. Insert the new blades and tighten the screws.

Remove both the Allen and hexagon spanner after com-

pleting the change.

5. Close the casing again and tighten the knob .

Empty the collection container

Remove the mains plug before any maintenance and

cleaning work!

Note

The locking lever has the function of a safety switch and must

be in Position

(2) while operating the product. If the locking

lever should not be correctly snapped in, this and the switch

must be cleaned in the product, if required.

1. Bring the locking mechanism to position 1.

2. Pull the collection container completely out of the frame.

3. Empty the container.

4. Slide the collection container onto the frame as far as it will go.

5. Bring the locking mechanism to position 2.

Fixing problems

Warranty

The warranty rules issued by our company or the importer apply to every

country. As part of the warranty, we remedy malfunctions on your appli-

ance free of charge provided that this malfunction is caused by a material

or manufacturing defect. In the event of a warranty claim, please turn to

your dealer or the nearest branch office.

Problem Possible cause Solution

Motor does not start.

Not connected to voltage supply

Check protection

Faulty connection cable

Check the cable (electrical expert)

Motor hums but does not start

Top of casing not closed properly (safety shutdown de-

vice is tripped)

Close top of casing properly and screw, re-

move dirt if required.

Blade unit blocked

Switch off appliance, remove mains plug

and clean appliance on the inside

Faulty capacitor

Give appliance to authorised WOLF-Gar-

ten customer service centre for repair.

Motor does not start.

Extension cable too long or cross section too small

Extension cable min. 1.5 mm², max. 25 m

long. In the case of longer cable cross sec-

tion min. 2.5 mm

Socket too far from main connection and connecting

lead cross section too small

Reduced cutting output

Dull blade.

Changing blades

When in doubt, always seek out a WOLF Service location.

Attention: Put down the appliance and pull out the power plug before performing any checks or work on the blades.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

WOLF-Garten SDE 2800 EVO Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info