723918
17
Zoom out
Zoom in
Vorherige Seite
1/19
Nächste Seite
17
EN
LED light indicator Status Action
Light does not turn on There is no power. Confirm that the power cord is connected properly to the
charger and that the charger is connected to a suitable
power supply.
Green light on Boundary wire is connected
successfully; Landroid
®
is fully
charged.
/
Green light flashing Boundary wire is connected in wrong
direction.
The Boundary Wire isn’t connected.
Check and reverse two ends of boundary wire.
Confirm that there are no breaks in the boundary wire.
Power supply is connected
successfully, while the wire is
connected unsuccessfully.
Check that the Boundary Wire has been connected
correctly to the charging base.
Confirm that there are no breaks in the boundary wire.
Red light on Landroid
®
is auto charging. /
4. Turn on and Test the Installation
Adjust the cutting height to its maximum level (60mm) for the
first mow. Adjust to your preferred grass height after the first cut.
Place your Landroid
®
inside the working area, a few meters
away from the charging base. Turn on Landroid
®
. It will travel
the entire boundary wire before returning to charging base.
This allows you to check that the boundary wire is laid out
properly.
Turn the main switch at the rear of Landroid
®
to Position “I”.
Wait until the battery indication light stays green. If Landroid
®
has low battery capacity, the battery indication light will stay
red. Press “ ” button and then press OK” button.
Watch the Landroid
®
as it returns to the charging base and
modify the position of the boundary wire if necessary. When
Landroid
®
successfully returns to the charging base, the
installation has been successfully completed!
NOTE: If the boundary wire is broken during the testing or
you find you need to extend the boundary wire, please refer
to “Joining the Boundary Wire” in Owners Manual for
instructions.
4.1
4.2
This is the exciting part: turn on your Landroid for the first time.
17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Worx WR102 SI wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Worx WR102 SI

Worx WR102 SI Bedienungsanleitung - Englisch - 20 seiten

Worx WR102 SI Installationsanweisung - Holländisch - 19 seiten

Worx WR102 SI Bedienungsanleitung - Holländisch - 21 seiten

Worx WR102 SI Installationsanweisung - Französisch - 19 seiten

Worx WR102 SI Bedienungsanleitung - Französisch - 21 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info