Bedienungsanleitung Worx WU420 (Seite 5 von 24) (Englisch)

673303

Zoom out

Zoom in

Vorherige Seite

1/24

Nächste Seite

Supports must be placed under the panel on both sides, near the

line of cut and near the edge of the panel.

e) Do not use dull or damaged blades. Unsharpened or

improperly set blades produce narrow kerf causing excessive

friction, blade binding and kickback.

f) Blade depth and bevel adjusting locking levers must be

tight and secure before making cut. If blade adjustment shifts

while cutting, it may cause binding and kickback.

g) Use extra caution when making a “plunge cut” into

existing walls or other blind areas. The protruding blade may

cut objects that can cause kickback.

SAFETY INSTRUCTIONS FOR PLUNGE- TYPE SAW

a) Check guard for proper closing before each use. Do not

operate the saw if guard does not move freely and enclose

the blade instantly. Never clamp or tie the guard with the

blade exposed. If saw is accidentally dropped, guard may be bent.

Check to make sure that guard moves freely and does not touch

the blade or any other part, in all angles and depths of cut.

b) Check the operation and condition of the guard return

spring. If the guard and the spring are not operating properly,

they must be serviced before use. Guard may operate sluggishly

due to damaged parts, gummy deposits, or a build-up of debris.

c) Assure that the guide plate of the saw will not shift while

performing the “plunge cut” when the blade bevel setting

is not at 90°. Blade shifting sideways will cause binding and likely

kick back.

d) Always observe that the guard is covering the blade before

placing saw down on bench or ﬂoor. An unprotected, coasting

blade will cause the saw to walk backwards, cutting whatever is

in its path. Be aware of the time it takes for the blade to stop after

switch is released.

GENERAL SAFETY WARNINGS FOR YOUR LASER

WARNING: Read all safety warnings and all instructions.

Failure to follow the warnings and instructions may result in serious

injury.

Save all warnings and instructions for future reference.

These lasers do not normally present an optical hazard although

staring at the beam may cause ﬂash blindness.

Do not stare directly at the laser beam. A hazard may exist if you

deliberately stare into the beam, please observe all safety rules as

follows:

The laser shall be used and maintained in accordance with the

manufacturer’s instructions.

Never aim the beam at any person or an object other than the work

piece.

The laser beam shall not be deliberately aimed at another person

and shall be prevented from being directed towards the eye of a

person for longer than 0.25 seconds area.

Always ensure the laser beam is aimed at a sturdy work piece

without reﬂective surfaces, e.g. wood or rough-coated surfaces

are acceptable. Bright shiny reﬂective sheet steel or similar is not

suitable for laser applications as the reﬂective surface may direct

the laser beam back at the operator.

Do not change the laser device with a different type. The

manufacturer or an authorized agent must carry out repairs.

CAUTION: Use of controls or adjustments other than those

speciﬁed herein may result in hazardous radiation exposure.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Worx WU420 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info