674722
8
Zoom out
Zoom in
Vorherige Seite
1/56
Nächste Seite
DR-2X / DR-2XE Operating Manual6
Connection for DR-2XE (European and Australian versions)
Follow the outline in the illustration regarding the proper connection for the required External Power Supply.
The DC power connector for the DR-2XE must only be connected to a DC source providing 13.8V DC (±15 %),
and capable of at least 10A of current.
Always observe proper polarity when making DC connection.
Make sure to switch OFF the power of the external power source before connecting.
1 Insert the connector of the provided DC power cord into the DC IN jack at the rear of the repeater.
2 Connect the red wire (+) of the provided DC power cord to the positive (+) terminal of the external power
source, and the black wire (-) to the negative (-) terminal.
+
(red)
Fuse (15 A)
(black)
The external power source should be installed near the equipment and should be easily accessible.
Permanent damage can result when improper supply voltage, or reverse-polarity voltage, is applied to the DR-2XE.
The Limited Warranty on this radio does not cover damage caused by application of AC voltage, reverse polarity
DC, or DC voltage outside the specified range of 13.8 V ±15 %. When replacing fuses, be certain to use a fuse of
the proper rating. The DR-2XE requires a 15A blade fuse.
Connecting External Devices
Connection of an external microphone
By connecting an optional microphone MH-48A6JA or MH-42C6J to the
[
MIC
]
jack on the front panel, voice
communications are possible in the mode which is set on the transmitter. Except when AMS is set on the
transmitter, data transmission is not available via the
[
MIC
]
jack.
Connection to a personal computer
The supplied PC connection cable “SCU-20” can be used to connect the repeater to a personal computer as
a USB port.
Use the
[
ACC
]
jack to connect with the optional WIRES-X Internet Linking Kit “HRI-200”.
The pin assignments of the
[
ACC
]
jack are as follows.
PKD (packet data input)
GND
PKS (PTT)
RX 9600 (9600 bps packet data output)
RX 1200 (1200 bps packet data output)
PK SQL (squelch control)
TXD (serial data output
[
repeater PC
]
)
RXD (serial data output
[
repeater PC
]
)
CTS (data communication control)
RTS (data communication control)
z Make sure to switch off the power to the radio before connecting the cable.
z When using the SCU-20, PC connection cable, a dedicated driver must be installed in the personal computer.
Download and use the driver and installation manual from the YAESU website.
8

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Yaesu DR-2X wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info