Bedienungsanleitung Yaesu DR-2X (Seite 32 von 56) (Englisch)

674722

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

DR-2X / DR-2XE Operating Manual30

13. Voice messages

Voice messages are a very useful feature to communicate messages to all club members. For example, when

you plan a breakfast meeting on Sunday morning, if you record the location and time with the remote control,

the message is transmitted from the repeater at a predetermined interval and number of times. For example,

it is possible to set the message to announce ten times at an hourly interval.

Voice Message for C4FM Digital Mode

Remote control voice message using FTM-400D, FTM-100D or FTM-3200D

Recording, playback, and erasing are performed with the “PTT” “P2” “P3” keys of the transceiver’s microphone.

In order to record a message, first register the transceiver DP-ID on the DR-2X/DR-2XE repeater.

1 Tune the transmit frequency to the uplink frequency of the CH-B side of the DR-2X/DR-2XE.

2 Set the transceiver to the C4FM digital mode, then press and hold the “” key on the microphone.

To record a message:

Press the PTT to record. When you release the PTT, recording will end automatically and “REC

Completed” will be displayed on the screen of the mobile transceiver.

Recording is possible for a maximum of 60 seconds.

To play and transmit the message:

Press the P2 key. The message will transmit once and “PLAY Completed” will be displayed on the screen

of the mobile transceiver.

To erase a recorded message:

When the P3 key is pressed, the recorded contents are deleted and “CLEAR Completed” is displayed on

the screen of the mobile transceiver.

3 Press the “” key on the microphone to return to the normal operation.

Voice Message for Analog FM

Send 4-digit DTMF codes from the transceiver's microphone to record, play, or erase a voice message.

1 Tune the transmit frequency to the uplink frequency of the CH-B side of the DR-2X/DR-2XE.

2 Set the transceiver to the analog FM mode.

To record a message:

While transmitting, press the “” key, then input the preset 4-digit command (initial value 5555) from

the microphone. When the PTT is released, a CW code of “R” is sent on the downlink frequency. Press

the PTT to record. When you release the PTT, recording stops automatically, and the CW code of “R” is

transmitted on the downlink frequency.

z If a CW code of “NG” is returned when recording starts, the recording area of the FVS-2 is full. Execute the erase

operation to clear the internal memory area.

z Recording is possible for a maximum of 60 seconds.

To play and transmit the message:

While transmitting, press the “” key, then input the preset 4-digit command (initial value 6666) from the

microphone. Once the message is transmitted, a CW code of “R” is sent on the downlink frequency.

To erase a recorded message:

While transmitting, press the “” key, then input the preset 4-digit command (initial value 7777) from

the microphone. The recorded content is erased and the CW code of “R” is transmitted at the downlink

frequency.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yaesu DR-2X Seite 32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info