444588
82
Zoom out
Zoom in
Vorherige Seite
1/104
Nächste Seite
Page 80 FT-450 OPERATION MANUAL
CWSPEED
Function: Sets the sending speed for the built-in
Electronic keyer.
Available Values: 4 wpm(20cpm)~60wpm(300cpm)
Default: 12wpm (60cpm)
You can set the sending speed in either: wpm (words
per minute), or cpm (characters per minute).
To switch between “Wpm” and “cpm”, just press the
[
F
]
button.
Note:
If the CW QSK is set to 25ms, the setting of CW
SPEED must not exceed 50wpm (250cpm); And if
the CW QSK is set to 30ms, the setting of CW SPEED
must not exceed 42wpm (210cpm). The delay will
make it impossible to transmit.
CWSTONE (CW SIDE TONE)
Function: Sets the CW sidetone volume level.
Available Values: FIX0 ~ FIX100 or
LNK-50 ~ LNK 0 ~ LNK+50
Default: FIX10 or LNK-8
CWTRAIN (CW TRAINING)
Function: Setting of CW training function
Available Values: N: / A: / M:
Default: N:
Sends random Morse Code five-character groups via
the sidetone.
N: Numeric characters only
A: Alphabet characters only
M: Numeric and Alphabet characters (Mixed)
CWWEIGT (CW WEIGHT)
Function: Sets the CW weight level.
Available Values: 1/2.5~1/4.5
Default: 1/3.0
Sets the Dot/Dash ratio for the built-in electronic keyer.
D DISP (DATA DISP)
Function: DIG (USER-L or USER-U) mode opera-
tion.
Available Values: -3000Hz ~ 0 ~ +3000Hz
Default: 0
Defines the displayed frequency offset during DIG
(USER-L or USER-U) mode operation.
D TYPE (DTAT MODE)
Function: Selects the mode and sideband (if appli-
cable) in the DIG (Digital) mode.
Available Values: RTTY/USR-L/USR-U
Default: RTTY
RTTY: FSK RTTY operation
USR-L: User-programmed custom operation based
on LSB mode
USR-U: User-programmed custom operation based
on USB mode
DIALSTP (DIAL STEP)
Function: Sets the DIAL knob's tuning speed.
Available Values: SSB/CW: 1 / 10 / 20 (Hz)
AM/FM: 100 / 200 (Hz)
Default: SSB/CW: 10 (Hz), AM/FM: 100 (Hz)
The width of the step of the
[
MAIN DIAL
]
knob can
be set for each mode.
DIG VOX
Function: Sets the gain of the VOX circuitry input
level for the DIG mode.
Available Values: OFF / 1~100
Default: OFF
EMERGEN (EMERGENCY)
Function: Enables Tx/Rx operation on the Alaska
Emergency Channel, 5167.5 kHz.
Available Values: ON/OFF
Default: OFF
When this Menu Item is set to “ON,” the spot fre-
quency of 5167.5 kHz will be enabled. To get to this
frequency, use the
[
DSP/SEL
]
knob to navigate. The
Alaska Emergency Channel will be found between
the Memory channel “US5-001” and “MEM-500.”
NOTE:
Use of this frequency is restricted to amateurs oper-
ating in (or within 92.6 km of) the U.S. State of Alaska,
and it is to be used for emergency communications
only (involving the immediate protection of life or prop-
erty).
KEYHOLD (KEY HOLD TIME)
Function: Sets the hold time for a push switch to
activate.
Available Values: 0.5 / 1.0 / 1.5 / 2.0
Default: 1.0
MENU MODE
82

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Yaesu FT-450 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info