444588
89
Zoom out
Zoom in
Vorherige Seite
1/104
Nächste Seite
Page 87FT-450 OPERATION MANUAL
I
NSTALLATION
OF
O
PTIONAL
A
CCESSORIES
AUTOMATIC ANTENNA TUNER ATU-450 OPERATION
The ATU-450 Automatic Antenna Tuner responds to control commands from the FT-450 Transceiver, providing
microprocessor-based impedance matching on the 160 through 6 meter amateur bands. The impedance matching
range is from 16.5 ohms to 150 ohms (up to 3:1 SWR). Accordingly, the ATU-450 should not be expected to
match “Long wire” type antennas unless you have taken specific design steps to ensure that the impedance
presented to the FT-450 is within this specification.
Important Note
Please be careful to avoid any short-circuit to any metal object.
Please install with great care to prevent injuries from sharp corners of metal objects.
Please practice standard grounding techniques and do not touch semiconductor components unnecessarily
to avoid breakage or damage by static electricity etc.
Cable Information
Connect the interconnecting Control Cable from the FT-450.
Connect the TMP plug (marked green) from the ATU-450 to J5402 on the MAIN Unit.
Connect the other TMP plug (marked gray) from the ATU-450 to J5404 on the MAIN Unit.
Installation
1. Turn off the FT-450’s POWER switch by pressing
and holding the
[
POWER
(
ON/OFF
)]
switch for one
second, and then turn off the External DC Power
Supply’s POWER switch.
2. Disconnect the power cable from the ~DC IN Jack
on the rear panel, and then disconnect all cables
from the FT-450.
3. Remove the two screws from each side and four
screws from the top case of the transceiver. Slide
the top case upward about 1 inch, then discon-
nect the speaker plug from the MAIN Unit and
remove the top case.
NOTE:
Because the speaker cable is connected to the
top case, please be careful not to break the
speaker cable.
4. Remove the two screws from each side and four
screws from the bottom case of the transceiver
and then remove the bottom case.
5. The ATU-450 mounting location is on the right side
of the bottom chassis. Insert the two coaxial cables
from the ATU-450 into this hole.
6. Connect the 6-pin plug from the ATU-450 to the
6-pin Jack.
7. Install the ATU-450 to the chassis while pulling
the two coaxial cables thru the chassis.
Through Hole
6-pin Connector
8. Mount the ATU-450 with the supplied four screws.
NOTE:
At the front side of the ATU-450, carefully lift the
rubber packing, which is around the transceiver
front panel, and install the two front screws. Do
not damage the packing or the top case may not
close.
Rubber Packing
ATU-450
89

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Yaesu FT-450 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info