478499
38
Zoom out
Zoom in
Vorherige Seite
1/132
Nächste Seite
36 FT-857D Operating Manual
ADJUSTING THE RF GAIN AND SQUELCH
The SQL/RF Gain control is configured differently,
depending on the country to which the FT-857D has
been exported. In the U.S. version, the default func-
tion of this control is “RF Gain.” The configuration of
the SQL/RF Gain control is set via Menu Mode No-
080
[
SQL/RF GAIN
]
; see page 110 for details.
If your transceiver is configured for “RF Gain” use, rotating this control fully clockwise in
the SSB/CW/Digital modes will provide best sensitivity. To reduce the receivers RF Gain
somewhat, rotate this control counter-clockwise slightly. You will observe an increasing
number of bars on the S-meter as you rotate the RF Gain control counter-clockwise; this
indicates increasing AGC voltage, which is causing the front-end gain to be reduced. In the
FM and Packet modes, with “RF Gain” selected, the FT-857D goes into an “Auto Squelch”
mode, with the Squelch level being preset at the factory.
If this control is configured for “SQL” operation, the FT-857Ds RF Gain will be set for
maximum sensitivity in all modes, and the SQL/RF Gain control will function solely as a
Squelch control. In this case, rotate the SQL/RF Gain control to the point where the back-
ground noise is just silenced; this will provide the best sensitivity to weak signals, while
keeping the receiver quiet when no signal is received. The LED just above the Main DIAL
will glow Green when the squelch is opened by an incoming signal or noise.
SETTING THE OPERATING FREQUENCY
1. In the “SSB/CW/DIG” modes, rotate the DIAL knob to set the frequency. Clockwise
rotation of the DIAL increases the operating fre-
quency.
2. In the “AM/FM/ PKT” modes, rotate the SELECT
knob to set the frequency. Clockwise rotation of
the SELECT knob increases the operating fre-
quency.
3. You may also use the SELECT knob to adjust the operating frequency in the “SSB/
CW/DIG” modes. The SELECT knob provides faster tuning, ideal for making quick
changes in frequency when you want to move across the band in a hurry. You can then
use the DIAL knob to make fine frequency adjustments.
The synthesizer steps for the SELECT knob may be adjusted independently by mode. Use
Menu Mode No-006
[
AM STEP
]
for AM, No-052
[
FM STEP
]
for FM, and No-082
[
SSB
STEP
]
for SSB/CW/DIG. See pages 97, 105, and 110 for details.
If you press the SELECT knob momentarily, then rotate the SELECT knob, you can now
OPERATION
SQL/RF
DIALSELECT
38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Yaesu FT-857D wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info