478499
66
Zoom out
Zoom in
Vorherige Seite
1/132
Nächste Seite
64 FT-857D Operating Manual
DIGITAL MODE OPERATION
(
SSB-BASED AFSK
)
monitor ALC voltage. If not, press the
[
FUNC
]
key momentarily, then rotate the SE-
LECT knob to select to select Multi Function Row “i”
[
MTR, –––, DISP
]
, then press
the
[
A
](
MTR
)
or
[
B
]
key so as to select metering of ALC (“ALC” icon will appear at the
upper of the
[
B
]
] key).
5. Press and hold in the
[
FUNC
]
key for one second to enter the Menu mode.
6. Rotate the SELECT knob to recall Menu Mode No-001
[
EXT MENU
]
, then rotate the
DIAL to change the setting to “ON” to enable the extended Menu Mode.
7. Rotate the SELECT knob to select Menu Mode No-037
[
DIG GAIN
]
.
8. Following the instructions for your TNC’s software, activate the transmitter from the
computer keyboard; this should cause the AFSK output from the TNC to be sent to the
radio. While transmitting, view the ALC meter; a few “dots” of ALC indi-
cation should be observed. If not, rotate the DIAL knob to adjust the AFSK
level within the FT-857D for 16 dots of indication on the ALC meter.
9. Press and hold in the
[
FUNC
]
key for one second to save the new AFSK level setting
and return to normal operation. You are now ready for full RTTY operation.
Because RTTY is a continuous-duty transmission mode, try to keep your trans-
missions short when running on battery power, so as to minimize current drain.
PSK31 Operation
Two dedicated PSK31 modes are available, one each for USB-side and LSB-side injection.
For BPSK work, the injection does not matter, but for QPSK the two working stations must
use the same sideband.
1. Connect the FT-857D to your computer’s sound card or interface.
2. Setup for PSK31 operation is basically identical to that previously described for RTTY
operation. As before, use the “DIG” mode. However, in Menu Mode No-038
[
DIG MODE
]
,
select “PSK31-L” (for LSB injection) or “PSK31-U” (for USB injection). As with RTTY,
Menu #38 may be used to set the drive to the transmitter. And the YF-122C 500 Hz
filter or YF-122CN 300 Hz filter may also be utilized, as described previously.
“USER” Defined Digital Modes
Also provided in the FT-857D are two convenient “USER” Digital modes, one each pro-
viding USB- and LSB-side injection, which may be used for SSTV, Fax, Pactor, and other
digital operating modes.
Here is an example involving the configuration of the USER mode for JT44 (WSJT) opera-
tion with USB-side injection (as opposed to LSB injection, used in the default “RTTY”
mode):
1. Use Menu Mode No-038
[
DIG MODE
]
to set the Digital mode to “USER-U.”
TRANSMITTER OPERATION
66

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Yaesu FT-857D wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info