Bedienungsanleitung Yaesu FT-897D (Seite 23 von 76) (Englisch)

478500

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Page 21FT-897D OPERATING MANUAL

OPERATION

LSB USB CW CWR

AMFMDIGPKT

MODE

MODE SELECTION

Press either the MODE

(



)

or MODE

(



)

key to move

among the eight settings for the operating modes, respec-

tively.

where “CWR” is “CW-Reverse,” using the opposite side-

band from the “default” BFO injection sideband (in most

cases, the default injection sideband is on the “USB” side);

“DIG” is an AFSK-based Digital mode, set up per Menu

Mode No-038

[

DIG MODE

]

; and “PKT” represents either

1200 or 9600 bps FM packet.

You can set VFOa and VFOb to different modes

in the same band, allowing you to have a

“Phone” VFO and a “CW” VFO, for example.

ADJUSTING THE AUDIO VOLUME LEVEL

Rotate the AF knob to set a comfortable listening level.

When operating in the “DIG” or “PKT” modes, you may

set the AF knob to any comfortable setting, or even all the

way off, because the output from the DATA jack is a fixed-

level audio signal.

Start with the AF knob set fully counter-clock-

wise, especially when using FM (the back-

ground noise on FM can be surprisingly loud)!

ADJUSTING THE RF GAIN AND SQUELCH

The SQL/RF Gain control is configured differently, depend-

ing on the country to which the FT-897D has been exported.

In the U.S. version, the default function of this control is

“RF Gain.” The configuration of the SQL/RF Gain control

is set via Menu Mode No-080

[

SQL/RF GAIN

]

; see page 62

for details.

If your transceiver is configured for “RF Gain” use, rotating

this control fully clockwise in the SSB/CW/Digital modes

will provide best sensitivity. To reduce the receiver’s RF

Gain somewhat, rotate this control counter-clockwise

slightly. You will observe an increasing number of bars on

the S-meter as you rotate the RF Gain control counter-clock-

wise; this indicates increasing AGC voltage, which is caus-

ing the front-end gain to be reduced. In the FM and Packet

modes, this control will automatically be set to “Squelch,”

even though the setting of Menu Mode No-080

[

SQL/RF

GAIN

]

is “RF Gain.” But if you set it this way, the SQL/RF

control has no effect on FM.

More accurately, this should say:

In the FM and Packet modes, with “RF Gain” selected, the

FT-897D goes into an “Auto Squelch” mode, with the

Squelch level being preset at the factory.

If this control is configured for “SQL” operation, the FT-

897D’s RF Gain will be set for maximum sensitivity in all

modes, and the SQL/RF Gain control will function solely

as a Squelch control. In this case, rotate the SQL/RF Gain

control to the point where the background noise is just si-

lenced; this will provide the best sensitivity to weak signals,

while keeping the receiver quiet when no signal is received.

The LED just above the Main Dial will glow Green when

the squelch is opened by an incoming signal or noise.

Battery consumption is significantly reduced if

the receiver is squelched, as the audio ampli-

fier stage is shut off when the receiver is muted.

BATT-B

BATT-A

MODE

BATT-B

BATT-A

BATT- B

BATT- A

SQL/RF

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yaesu FT-897D Seite 23

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info