478500
42
Zoom out
Zoom in
Vorherige Seite
1/76
Nächste Seite
Page 40 FT-897D OPERATING MANUAL
WEATHERFAX MONITORING
Monitoring of HF WeatherFax broadcasts is easily accom-
plished using the FT-897D.
Before proceeding, be certain that the WeatherFax demodu-
lator is properly connected to Pins 5 and 2 of the rear panel
DATA jack.
1. Set the transceiver to the VFO mode, and set the operat-
ing mode to “DIG,” setting Menu Mode No-038
[
DIG
MODE
]
to “PSK31-U,” as described previously.
2. Now, select the operating frequency of the station trans-
mitting the WeatherFax broadcast. Note that, in the USB
mode, the frequency you should program onto the dis-
play is typically 1.90 kHz below the station’s “assigned”
frequency. Thus for a WeatherFax station assigned to
8.682.0 MHz, tune to 8.680.1 MHz.
3. When the WeatherFax broadcast begins, no further op-
erator intervention should be needed from the transceiver
standpoint. The audio level from the DATA jack on the
rear of the transceiver is fixed, and cannot be adjusted.
4. Fine adjustments in the gray-scale and the frame align-
ment are accomplished using the computer and software
connected to your WeatherFax demodulator.
TIME-OUT TIMER
Most often used on FM, the transmitters Time-Out Timer
(TOT) feature disables the transmitter after a user-defined
period of transmission. This feature may be useful in pre-
venting a “stuck microphone” (accidental closure of the PTT
switch) from causing interference to other users, and it will
also force you to keep your transmissions short, thereby
conserving battery power.
To activate the Time-Out Timer:
1. Press and hold in the
[
F
]
key for one second to enter the
Menu mode.
2. Rotate the MEM/VFO CH knob to recall Menu Mode
No-084
[
TOT TIME
]
.
The default setting for this feature is “OFF.” Rotate the
DIAL knob to set a new time-out setting (from 1 minute
to 20 minutes).
3. When you have made your selection, press and hold in
the
[
F
]
key for one second to save the new setting and
exit to normal operation.
SPLIT FREQUENCY OPERATION
This transceiver provides convenient split-frequency opera-
tion, using the VFO-A and VFO-B, for DX working and
other operating situations requiring unique split frequency
pairs.
The example below will describe a typical split-frequency
DX situation on the 20-meter band, with a DX station trans-
mitting on 14.025 MHz, listening 10 kHz higher in the band.
1. Set VFO-A to 14.035.00 MHz CW (DX station’s listen-
ing frequency).
2. Press the
[
F
]
key momentarily, then rotate the MEM/
VFO CH knob, as needed, until Multi Function Row
“a”
[
A/B, A=B, SPL
]
appears on the display.
3. Press the
[
A
](
A/B
)
key momentarily to select VFO-B.
4. Tune the VFO-B frequency to 14.025.00 MHz (DX
station’s transmitting frequency).
5. Press the
[
C
](
SPL
)
key momentarily. The transceiver will
now transmit using the VFO-A frequency, and will re-
ceive using the VFO-B frequency.
“Parentheses” will appear on the both sides of the “SPL
indication, and the “SPL” icon will appear at the upper
left corner of the display.
6. To listen to the pile-up calling the DX station (so as to
align your frequency more closely to that of the station
being worked by the DX), press the
[
A
](
A/B
)
key to re-
verse the VFOs. You will now be tuning in the vicinity
of 14.035 MHz, and you can zero in on the DX station’s
listening frequency by tuning in on the station in QSO
with the DX. Press the
[
A
](
A/B
)
key again to return to
reception on the DX station’s frequency.
7. Press the
[
C
](
SPL
)
key once more to cancel split opera-
tion; the “Parentheses” and “SPL” icon will disappear
from the display.
TRANSMITTER OPERATION
42

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Yaesu FT-897D wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info