Bedienungsanleitung Yaesu FT-897D (Seite 56 von 76) (Englisch)

478500

Zoom out

Zoom in

Vorherige Seite

1/76

Nächste Seite

Page 54 FT-897D OPERATING MANUAL

Available Values Default

ON/OFF OFF

ON/OFF 1

ENABLE/DISABLE DISABLE

0 ~ 100 50

2.5/5/9/10/12.5/25kHz 1

OFF/1h ~ 6h OFF

OFF/RANGE/ALL RANGE

ON/OFF OFF

– YAESU

––

OFF/1 sec ~ 255 sec OFF

440/880/1760 Hz 880 Hz

0 ~ 100 50

–300 ~ +300 Hz 0 Hz

4800bps/9600bps/38400bps 4800bps

CAT/LINEAR/TUNER CAT

CLAR, M/V, MAIN CLAR

ON/OFF OFF

USB/LSB/AUTO USB

FULL/30 ~ 3000 msec 250 msec

NORMAL/REVERSE NORMAL

ELEKEY/MICKEY ELEKEY

400 ~ 800 Hz 700 Hz

10/15/20/25/30 ms 10 ms

0 ~ 100 50

4 ~ 60 wpm (1wpm/step)/ 12 wpm

20 ~ 300 cpm (5cpm/step) (60 cpm)

N, A, AN N

1:2.5 ~ 1:4.5 1:3.0

104 Standard DCS codes 023

Tn-Rn/Tn-Riv/Tiv-Rn/Tiv-Riv Tn-Rn

FINE/COARSE FINE

–3000 ~ +3000 Hz 0 Hz

0 ~ 100 50

RTTY-L/RTTY-U/PSK31-L/ RTTY-L

PSK31-U/USER-L/USER-U

–3000 ~ +3000 Hz 0 Hz

Function

Enables/Disables the extended Menu Mode.

Activates/deactivates the Automatic Repeater Shift feature when

operating on the 144 MHz band.

Activates/deactivates the Automatic Repeater Shift feature when

operating on the 430 MHz band.

Enabling/disabling the DIAL knob on the AM and FM modes.

Adjusts the microphone gain level for the AM mode.

Selects the tuning steps for the MEM/VFO CH knob on the AM mode.

Selects the Auto Power Off time (time before power goes off).

Selects the ARTS beep mode.

Enables/disables the CW identifier during ARTS operation.

Stores your callsign into the CW identifier.

Stores the message for the Beacon.

Selects the interval time (between message and message).

Selects the beep frequency.

Selects the beep volume level.

Sets the Rx Carrier Point for LSB.

Sets the Tx Carrier Point for LSB

Sets the Rx Carrier Point for USB

Sets the Tx Carrier Point for USB

Sets the transceiver’s circuitry for the CAT baud rate to be used.

Selects the device which is connected to the CAT/LINEAR jack

on the rear panel.

Defines the “control” knob to be used for setting of the clarifier

offset frequency.

Selects whether the KEY jack shall be “Enabled” or “Disabled”

while using the SSB/FM modes.

Sets the CW carrier oscillator injection side on the CW mode.

Sets the receiver recovery time during pseudo-VOX CW semi-

break-in operation.

Sets the keyer paddle’s wiring configuration.

Enables/disables CW keying by the microphone’s [UP]/[DWN]

keys.

Setting of the pitch of the CW sidetone, BFO offset, and CW filter

center frequencies.

Selects the time delay between when the PTT is keyed and the car-

rier is transmitted during QSK operation when using the internal keyer.

Setting of the CW sidetone volume level.

Sets the sending speed for the built-in Electronic keyer.

Sends random Morse Code five-character groups via the sidetone.

Sets the Dot:Dash ratio for the built-in electronic keyer.

Setting of the DCS code.

Selects “Normal” or “Inverted” DCS coding.

Setting of the DIAL knob’s tuning speed.

Defines the displayed frequency offset during DIG (USER-L or

USER-U) mode operation.

Adjusts the audio input level from terminal equipment during DIG

(Digital) mode operation.

Selects the mode and sideband in the DIG (Digital) mode.

Defines the carrier frequency offset during DIG (USER-L or USER-

U) mode operation.

No Menu Item

001 EXT MENU

002 144MHz ARS

003 430MHz ARS

004 AM&FM DIAL

005 AM MIC GAIN

006 AM STEP

007 APO TIME

008 ARTS BEEP

009 ARTS ID

010 ARTS IDW

011 BEACON TEXT 1

012 BEACON TIME

013 BEEP TONE

014 BEEP VOL

015 CAR LSB R

016 CAR LSB T

017 CAR USB R

018 CAR USB T

019 CAT RATE

020 CAT/LIN/TUN

021 CLAR DIAL SEL

022 CW AUTO MODE

023 CW BFO

024 CW DELAY

025 CW KEY REV

026 CW PADDLE

027 CW PITCH

028 CW QSK

029 CW SIDE TONE

030 CW SPEED

031 CW TRAINING

032 CW WEIGHT

033 DCS CODE

034 DCS INV

035 DIAL STEP

036 DIG DISP

037 DIG GAIN

038 DIG MODE

039 DIG SHIFT

The Menu System allows you to customize a wide variety of transceiver performance aspects and operating characteristics.

Once you have gone through the various Menu customization procedures initially, you will find that you will not have to resort

to them frequently during everyday operation.

MENU OPERATION

1) In step 3 above, if you press the [HOME] key

momentarily, it will reset the setting of that

Menu Item to its factory-default value.

2) In step 4 above, if you press the [C] key momentarily,

you will exit to normal operation without saving the new

setting.

3) In step 2 above, press the [A] key momentarily, The

“hyphen” in the Menu channel number will change to

become a “dot”; this shows that this Menu now is not in-

cluded in the recall the Menu Item loop.

MENU OPERATION

1. Press and hold in the

[

]

key for one second. The Menu

Item number and a title for the Menu Mode will appear

in the display.

2. Rotate the MEM/VFO CH knob to select the Menu Item

you wish to work on.

3. When you have chosen the desired Menu Item number,

rotate the DIAL knob to change the value or condition

for the Menu Item.

4. When you have made your selection, press and hold in

the

[

]

key for one second to save the new setting and

exit to the normal operation.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yaesu FT-897D Seite 56

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info