478500
67
Zoom out
Zoom in
Vorherige Seite
1/76
Nächste Seite
Page 65FT-897D OPERATING MANUAL
POWER-ON MICROPROCESSOR RESET
PROCEDURES
Some or all transceiver settings can be reset to their factory-
default states using one of the following power-on routines:
[
V/M
]
+ POWER on: Resets all memories and follow-
ing menu settings to their factory-default values:
Menu #06 (AM STEP), 33 (DCS CODE), 52 (FM STEP),
56 (MEM TAG), 76 (RPT SHIFT), 82 (SSB STEP), and
83 (TONE FREQ).
[
F
]
+ POWER on: Resets all menu settings (except the
following menu items) to their factory-default values.
Menu #06 (AM STEP), 33 (DCS CODE), 52 (FM STEP),
56 (MEM TAG), 76 (RPT SHIFT), 82 (SSB STEP), and
83 (TONE FREQ).
[
HOME
]
+ POWER on: CPU master reset for all memo-
ries and menu settings.
CLONING
You can transfer all data stored in one transceiver to another
set by utilizing the handy “Cloning” feature. This requires a
user-constructed cloning cable which connects the CAT/
LINEAR jacks on the two transceivers, as shown below.
TX D
TX D
RX D
GND GND
RX D
To clone from one transceiver to another, use the following
procedure:
1. Insert the Clone Cable into the CAT/LINEAR jack of
each transceiver.
2. Turn both transceivers off, then press and hold in the
MODE
(
)
and MODE
(
)
but-
tons on each radio while turning
the power on again. The “CLONE
MODE” notation will appear on
the display.
3. On the “destination” radio, press
the
[
A
]
key.
4. Now, on the “source” radio, press
the
[
C
]
key. Data will now be
transferred to the “Destination”
radio from the “Source” radio.
5. If there is a problem during the
cloning process, “Error” will be
displayed.
Check your cable connections
and try again.
6. If cloning is successful, turn the
“destination” radio off. Now turn
the “source” radio off.
7. Remove the clone cable. Channel and operating data for
both radios are now identical. They both may be turned
on now for normal operation.
[
Sourcu radio
]
[
Distination radio
]
P
OWER
-
ON
M
ICROPROCESSOR
R
ESET
P
ROCEDURES
/ C
LONING
67

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Yaesu FT-897D wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info