Bedienungsanleitung Yaesu FT-991 (Seite 75 von 154) (Englisch)

674740

Zoom out

Zoom in

Vorherige Seite

1/154

Nächste Seite

Page 73

FT-991 OperaTing Manual

Split operAtion uSing the tx clAriFier

For split TX/RX operation in “casual” pile-ups, where the split is less than 10 kHz, the TX Clarier (Offset Tuning) fea-

ture may be utilized.

1. Press the

MENU(SETUP)

button to enter the Menu

mode.

2. Rotate the

MULTI

knob to select Menu item “

040

CLAR MODE SELECT

”.

3. Touch

[

SELECT

] on the LCD, then rotate the

MULTI

knob to set this Menu item to “

” (the de-

fault setting is “

”).

CLAR/VFO-B Knob

CLAR Button

MULTI Knob

MENU(SETUP) Button

F$QEV

%.#4 /1&' '56.'%

#/ .% 6715. 2'



#/ .% 67'(4 3 1((



4. Touch

[

ENTER

]

on the LCD to save the new set-

ting.

%.#4 /1&' '56.'% 6:

F$QEV#/ .% 6715. 2'

#/ .% 67'(4 3 1((



5. Press the

MENU(SETUP)

button or touch

[

BACK

]

on the LCD to exit to normal operation.

6. Press the

CLAR

button. The “

” icon will appear

in the TFT display.

quick point:

The Clarifier is frequently used for receiver offset

tuning. However, for DX pile-ups where the DX

station is using a split of less than 10 kHz, the TX

Clarier function is usually the quickest way to set

the transmitter to the desired offset frequency.

7. Rotate the

CLAR/VFO-B

knob to set the desired

transmitter offset. A maximum split of ±9.999 kHz

may be set.

8. To exit from TX Clarier operation, press the

CLAR

button once more. The “

” icon will disappear

from the display.

Advice:



When listening to a “pile-up” calling a DX station, in

order to nd the station currently being worked, you

may press the

CLAR

button. Then, use the

CLAR/

VFO-B

knob to zero in on the station calling the DX

(use the SPOT function on CW for precise alignment

of your frequency). You may then press the

CLAR

button again to cancel the RX Clarier, and return to

reception on the DX station’s frequency.



Just as with receiver Clarier operation, the amount

of offset from the original VFO frequency will ap-

pear in the display.



As with receiver Clarier operation, when you turn

the TX Clarier off, the last-used offset is remem-

bered, and will be available if you turn the TX Clari-

er back on. To clear the Clarier offset, press and

hold the

CLAR

button for more than 1 second.

quick point:

When attempting to work a DX station on CW in a split

frequency pile-up, remember that a large number of oth-

er stations may also be using Yaesu transceivers with ca-

pability similar to that of your

FT-991

. On the DX side

of the pile-up, everyone calling precisely on the same

CW frequency will sound like a single tone! So you may

have more success if you use the RX Clarier to nd a

hole in the pile-up, instead of trying to zero-beat the last

station worked by the DX station.

transMitter convenience features

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yaesu FT-991 Seite 75

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info