674740
84
Zoom out
Zoom in
Vorherige Seite
1/154
Nächste Seite
Page 82
FT-991 OperaTing Manual
cW Spotting
(
zero-beAting
)
“Spotting” (zeroing in on a received CW station) is a handy technique to ensure you and the other station are precisely
on the same frequency.
The Tuning Offset Indicator in the display may also be observed so you can adjust the receiver frequency to center the
incoming station on the pitch corresponding to that of your transmitted signal.
Using the Auto Zeroing System
Press the
F(M-LIST)
button, then touch
[
ZIN
]
on the
LCD to cause the receiving frequency to zero-in auto-
matically while receiving the CW signal.
F(M-LIST) Button
Using the SPOT System
1. Press the
F(M-LIST)
button to display the function
list.
2. Touch
[
MONI
]
on the LCD. The Monitor function
will be set to “
ON
”. The
MULTI
knob will function
as the MONITOR adjustment knob.
F(M-LIST) Button
MONI (Monitor) indicator
MONI (Monitor) level indicator
3. Touch
[
SPOT
]
on the LCD. While you are press-
ing and holding
[
SPOT
]
, the tone is output from the
speaker.
Advice:
In a tough DX pile-up, you may actually want to
use the SPOT system to nd a “gap” in the spread
of calling stations, instead of zeroing in precisely
on the last station being worked by the DX station.
From the DX side, if a dozen or more operators (also
using Yaesu’s SPOT system) all call precisely on the
same frequency, their dots and dashes merge into a
single, long tone that the DX station cannot decipher.
In such situations, calling slightly higher or lower in
frequency may get your call through.
quick pointS:
The displayed frequency on CW normally reflects
the “zero beat” frequency of your offset carrier. That
is, if you were to listen on USB on 14.100.00 MHz
to a signal with a 700 Hz offset, the “zero beat” fre-
quency of that CW carrier would be 14.100.70 MHz;
the latter frequency is what the
FT-991
displays, by
default. However, you can change the display to be
identical to what you would see on SSB by using
Menu item “
059 CW FREQ DISPLAY
” and setting
it to “
DIRECT FREQ
” instead of the default “
PITCH
OFFSET
” setting.
cw convenience features
84

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Yaesu FT-991 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info