674740
99
Zoom out
Zoom in
Vorherige Seite
1/154
Nächste Seite
Page 97FT-991 OperaTing Manual
convenient MeMory FunctionS
The
FT-991
contains ninety-nine regular memories, labeled “
01
” through “
99
”, nine special programmed band edge
memory pairs, labeled “
P-1L
/
P-1U
” through “
P-9L
/
P-9U
”, and ve QMB (Quick Memory Bank) memories. Each mem-
ory stores various settings, in addition to the VFO-A frequency and mode, but also stores the various settings shown be-
low. By default, the 99 regular memories are contained in one group; however, they can be arranged in up to six separate
groups, if desired.
quick point:
The
FT-991
memory channels store the following
data (not just the operating frequency):
VFO-A Frequency
VFO-A Mode
Clarier status and its Offset Frequency
IPO status
Attenuator status
Noise Blanker status
IF SHIFT and WIDTH status
CONTOUR status and its Peak Frequency
DSP Noise Reduction (DNR) status and its
Reduction algorithm selection.
DSP Notch lter (NOTCH) status
NAR bandwidth status
DSP Auto Notch lter (DNF) status
Repeater Shift Direction
CTCSS Tone information (CTCSS Encode,
Decode ON/OFF; Tone Frequency)
DCS information (DCS On/Off, DCS Code)
MeMorY operation
qMb MeMory bAnk
regulAr MeMory chAnnelS
pMS MeMory chAnnelS
01
97
P-7L/7U
P-6L/6U
P-5L/5U
P-4L/4U
02
98
P-8L/8U
03
99
P-9L/9U
P-1L/1U
P-2L/2U
P-3L/3U
qMb
(
quick MeMory bAnk
)
The Quick Memory Bank consists of ve memories independent from the regular and PMS memories. The QMB mem-
ories can quickly store operating parameters for later recall.
QMB Channel Storage
1. Tune to the desired frequency on VFO-A.
2. Press and hold the
RCL/STO
button for one second.
The “beep” will confirm that the VFO-A contents
have been written to the currently available QMB
memory.
Repeated one second presses of the
RCL/STO
but-
ton will write the VFO-A contents to successive QMB
memories.
Once all ve QMB memories have data on them, previ-
ous data will be over-written on a rst-in, rst-out basis.
QMB Channel Recall
1. Press the
RCL/STO
button briefly. The current
QMB channel data will be shown on the frequency
display area. The
QMB
icon will also appear and
the Memory Mode indicators in the LED indicators
area will illuminate.
2. Repeated brief presses of the
RCL/STO
button will
toggle through the QMB channels.
3. Press the
V/M
button to return to the VFO or Memo-
ry mode.
RCL/STO Button
V/M Button
Advice:
Rotating the Main Tuning Dial knob, or changing the
operating mode, will place the transceiver in the “Mem-
ory Tune” mode, which is a temporary “pseudo-VFO”
method of tuning off of a stored memory channel. If you
do not over-write the contents of the current memory
channel, the original contents will not be disturbed by
the initiation of Memory Tune operation.
99

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Yaesu FT-991 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info