674740
109
Zoom out
Zoom in
Vorherige Seite
1/154
Nächste Seite
Page 107FT-991 OperaTing Manual
vfo anD MeMorY scanninG
vFo ScAnning
Either the VFO or the memory channels of the
FT-991
may be scanned, and the receiver will halt scanning on any fre-
quency with a signal strong enough to open the receiver squelch.
1. Set the VFO-A to the frequency on which you would
like to begin scanning.
2. Press the
F(M-LIST)
button, then touch
[
SQL
]
on
the LCD. Rotate the
MULTI
knob so that the back-
ground noise is just silenced.
F(M-LIST
)
Button
MULTI Knob
3. Press and hold in the microphone
UP
or
DWN
but-
ton for one second, or press the
F(M-LIST)
button
followed by
[
SCAN
]
to start scanning in the speci-
ed direction on the VFO frequency.
4. If the scanner halts on an incoming signal, the deci-
mal point between the “MHz” and “kHz” digits of
the frequency display will blink.
Advice:
If the incoming signal disappears, scanning will
resume in about ve seconds.
On the SSB/CW and SSB-based Data modes, the
scanner will pause on a received signal, then will
step across the signal very slowly, giving you
time to stop the scan, if you like. In these modes
on the VFO, the scanner does not stop, however.
5. To cancel scanning, press the
PTT
switch, or touch
[
SCAN
]
on the LCD.
Advice:
If the scan has paused on a signal, pressing the mi-
crophone
UP
or
DWN
button, or touching
[
SCAN
]
on the LCD will cause scanning to resume instantly.
If you press the microphone
PTT
button during
scanning, the scanner will halt at once. However,
pressing the
PTT
button during scanning will not
cause transmission.
The manner in which the scanner resumes after it has
paused on a signal may be selected by using Menu
item “
038 MIC SCAN RESUME
”. The default “
TIME
(5 sec) setting will cause the scanner to resume scan-
ning after five seconds; however the scan setting
may be changed to resume only after the received
signal has dropped out.
If the Main Tuning Dial knob is rotated while scan-
ning is in progress, the scanning will continue up
or down in frequency according to the direction of
the Dial Knob rotation. (in other words, if the dial
is rotated to the left when scanning toward a higher
frequency, the direction of the scan will reverse.)
quick point:
If you have no interest in scanning, and wish to prohibit
the microphone
UP
/
DWN
buttons from initiating scan-
ning, you may disable scanning control from the mi-
crophone using Menu item
037 MIC SCAN
(set it to
DISABLE
”).
109

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Yaesu FT-991 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info