Bedienungsanleitung Yaesu FTDX1200 (Seite 11 von 140) (Englisch)

674747

Zoom out

Zoom in

Vorherige Seite

1/140

Nächste Seite

Page 9FT

1200 OPERATING MANUAL

INSTALLATION AND INTERCONNECTIONS

PROPER GROUND CONNECTION

GND

Transceiver

GND

Linear

Amplifier

GND

TNC

"Dais

Chain"

GND

Linear

Amplifier

GND

TNC

GND

Transceiver

IMPROPER GROUND CONNECTION

GROUNDING

The

1200

transceiver, like any other HF communications apparatus, reTuires an effective ground system for maxi-

mum electrical safety and best communications effectiveness. $ good ground system can contribute to station ef¿ciency

in a number of ways



It can minimi]e the possibility of electrical shock to the operator.



It can minimi]e 5F currents Àowing on the shield of the coaxial cable and the chassis of the transceiver. such cur-

rents may lead to radiation, which can cause interference to home entertainment devices or laboratory test eTuip-

ment.



It can minimi]e the possibility of erratic transceiveraccessory operation caused by 5F feedback andor improper

current Àow through logic devices.

$n effective earth ground system may take several forms. for a more complete discussion, see an appropriate 5F engi-

neering text. The information below is intended only as a guideline.

Typically, the ground connection consists of one or more copper-clad steel rods, driven into the ground. If multiple

ground rods are used, they should be positioned in a “V” con¿guration and bonded together at the base of the “V” which

is nearest the station location. Use a heavy, braided cable such as the discarded shield from type 5G-13 coaxial cable)

and strong cable clamps to secure the braided cables) to the ground rods. Be sure to weatherproof the connections

to ensure many years of reliable service. Use the same type of heavy, braided cable for the connections to the station

ground bus described below).

Inside the station, a common ground bus consisting of a copper pipe of at least  mm diameter should be used. $n al-

ternative station ground bus may consist of a wide copper plate single-sided circuit board material is ideal) secured to

the bottom of the operating desk. Grounding connections from individual transceivers, power supplies, and data com-

munications devices T1Cs, etc.) should be made directly to the ground bus using a heavy, braided cable.

'o not “'aisy-Chain” ground connections from one electrical device to another and thence to the ground bus. This

method may nullify any attempt at effective radio freTuency grounding. See the drawing below for examples of proper

grounding techniTues.

Inspect the ground system - inside the station as well as outside - on a regular basis to ensure continued performance

and safety.

Besides following the above guidelines carefully, note that household or industrial gas lines must never be used in an

attempt to establish an electrical ground. Cold water pipes may, in some instances, help in the grounding effort, but gas

lines represent a signi¿cant explosion ha]ard, and must never be used.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yaesu FTDX1200 Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info