Bedienungsanleitung Yaesu FTDX1200 (Seite 35 von 140) (Englisch)

674747

Zoom out

Zoom in

Vorherige Seite

1/140

Nächste Seite

Page 33FT

1200 OPERATING MANUAL

momentary presses of the

[

]

0H] band button.

(ach $mateur band button may similarly have up

to three freTuencymode settings applied.



When the

[

MHz/μT

]

button located to the left of

the

[

VFO-B/CLAR

]

knob) is pressed, the “

MHz

”

notation will appear in the display, and then rota-

tion of the

[

VFO-B/CLAR

]

knob will change the

freTuency in 1 0H] steps.

6. 3ress the

[

ANT

]

button to select the ap-

propriate antenna for the band in use.

DVICE:

When you make an antenna selection,

that antenna is “remembered” by the

microprocessor in conjunction with the

VF2 register in use.

7. 3ress the

[

MODE

]

button to select the

desired operating mode.

5epeated presses of the

[

MODE

]

button step through the available se-

lections.

3ressing and holding the

[

MODE

]

button will toggle to the alternate

mode.

For example, In the LSB or USB modes, pressing

and holding the

[

MODE

]

button toggles between

“LSB” and “USB” mode.

DVICE:



By convention in the $mateur bands, LSB is

used on the 7 0H] and lower bands with the

exception of 60 meters), while USB is utili]ed on

the 14 0H] and higher bands.



When changing modes from SSB to CW, you

will observe a freTuency shift on the display.

This shift represents the BF2 offset between the

“]ero beat” freTuency and the audible CW pitch

tone) you can hear the pitch is programmed via

the 0enu item “

066 CW FREQ DISPLAY

”), even

1. Turn on the external 'C power supply.

. 3ress and hold in the front-panel

[

ON/OFF

]

switch

until the transceiver turns on. $fter

about five seconds ten seconds if the

optional -Tuning .it is connected), the

transceiver is ready for full operation.

3. The transceiver will start up on 7.000.000 0H]

LSB, or the previously used operating freTuency)

and normal operation may begin.

OTE:

To turn power off, press and hold in the front panel

[

ON/OFF

]

switch for one second.

4. 5otate the

[

]

knob to set a com-

fortable audio level of the incoming

signals or noise. Clockwise rotation

of the

[

]

knob increases the vol-

ume level.

OTE:

When using headphones, start by rotating the

[

]

knob counter-clockwise, then bring the volume level

up after you put the headphones on. This will mini-

mi]e the chance of damage to your hearing caused

by an unexpectedly high audio level.

. 3ress an appropriate

[

BAND

]

key corresponding to

the $mateur band on which you wish to begin opera-

tion.

DVICE:



2ne-touch selection of each

$mateur band between 1.8

and 0 0H] is provided.



The

1200

utili]es a triple band-stack VF2

selection techniTue, which permits storing up to

three favorite freTuencies and modes onto each

VF2 band register. For example, you may store

one freTuency each on 14 0H] CW, 5TTY, and

USB, then recall these freTuencies by successive,

Here is the typical start-up procedure for normal operation

[

POWER

]

Switch

[

]

Knob

Main Tuning Dial Knob

[

BAND

]

Keys

BASIC OPERATION:

RECEIVING ON AMATEUR BANDS

[

MODE

]

Button

[

ANT

]

Switch

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yaesu FTDX1200 Seite 35

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info