Bedienungsanleitung Yaesu FTDX1200 (Seite 38 von 140) (Englisch)

674747

Zoom out

Zoom in

Vorherige Seite

1/140

Nächste Seite

Page 36 FT

1200 OPERATING MANUAL

BASIC OPERATION:

RECEIVING ON AMATEUR BANDS

CLAR

(

CLARIFIER

)

PERATION

The

[

RX CLAR

]

[

TX CLAR

]

[

CLEAR

]

buttons and

[

VFO-B/CLAR

]

knob are used to offset the receive freTuency,

the transmit freTuency, or both, from their settings on the VF2-$ freTuency. Four small numbers on the TFT 'isplay

show the current Clari¿er offset. The Clari¿er controls on the

1200

are designed to allow you to preset an offset up

to . kH]) without actually retuning, and then to activate it via the Clari¿er

[

RX CLAR

]

and

[

TX CLAR

]

buttons.

This feature is ideal for following a drifting station, or for setting the small freTuency offsets sometimes utili]ed in ';

“Split” work.

Here is the techniTue for utili]ing the Clari¿er

1. 3ress the

[

RX CLAR

]

button. The “

” notation

will appear in the TFT 'isplay, and the programmed

offset will be applied to the receive freTuency.

. 5otation of the

[

VFO-B/CLAR

]

knob will allow

you to modify your initial offset on the Ày. 2ffsets of

up to . kH] may be set using the Clari¿er.

To cancel Clari¿er operation, press the

[

RX CLAR

]

but-

ton. The “

” notation will disappear from the display.

DVICE:



Turning the Clari¿er off merely cancels the applica-

tion of the programmed offset from the receive and

or the transmit freTuencies. To clear the Clarifier

offset, and reset it to “]ero,” press the

[

CLEAR

]

but-

ton. The programmed offset is displayed in the small

multi-channel window of the freTuency display.



The Clari¿er operation including the offset freTuen-

cy) will be memori]ed independently on each VF2

stack of VF2-$ and VF2-B.

[

VFO-B/CLAR

]

Knob

[

RX CLAR

]

Button

[

TX CLAR

]

Button

[

CLEAR

]

Button

TXCLAR

$lternately, you may apply the Clarifier offset

to the transmit freTuency, without changing the

receive freTuency typically, for “split” '; pile-

ups).

[

VFO-B/CLAR

]

Knob

[

]

Button

7KH7XQLQJ2IIVHW,QGLFDWRUSURYLGHVDJUDSKLFDOUHSUHVHQWDWLRQRIWKH&ODUL¿HURIIVHW

In CW mode the factory default setting of the Tuning 2ffset Indicator shows the

CW Center Tuning, instead of Clari¿er 2ffset. If you wish to change this so that the

Clari¿er 2ffset is also displayed on CW, use the following procedure

[

SELECT

]

Button

1. 3ress the

[

]

button to enter the 0enu

mode.

. 5otate the

[

VFO-B/CLAR

]

knob or press the



button) to select 0enu item “

011 BAR

DISPLAY SELECT

”.

3. 3ress the

[

SELECT

]

button, then rotate the

[

VFO-B/CLAR

]

knob or press the



button)

to select “

CLAR

Clari¿er)” replacing the default

“

CW TUNE

CW TU1I1G)” selection).

4. 3ress the

[

SELECT

]

button, then press the

[

]

button to save the new setting and exit

to normal operation.

[

]

Button

[

Plus

(

)

Offset

]

[

Zero Offset

]

[

Minus

(–)

Offset

]

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yaesu FTDX1200 Seite 38

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info