478469
32
Zoom out
Zoom in
Vorherige Seite
1/116
Nächste Seite
30 FTM-10R OPERATING MANUAL
SMART MENU FEATURES
SCAN FEATURE
1. Press the top panel / key to select “SCAN”.
2. Press the key to initiate upward scanning.
When the scanner encounters a signal strong enough to open
the squelch, the scanner will halt for five seconds, and then
resume scanning.
3. To stop the scanner, press the or PTT key.
When the key function is set to “SCAN” via the top panel / key, the key
may be used as the scan start/stop command key.
If you want to change the direction of the scan while it is underway, rotate the DIAL
knob one click in the opposite direction (in this case, one click counter-clockwise). You
will see the scanner reverse direction and scan down in frequency.
The decimal point of the frequency display will blink while the Scan is activated.
You may select the Scan Resume mode via the Menu Item “F32 SCN MODE”.
When you start the scanner in the memory mode, only the memorized memory channels
will be scanned
SMART SEARCH
TM
OPERATION
The Smart Search feature allows you to load frequencies automatically according to where
activity is encountered by your radio. When Smart Search is engaged, the transceiver will
search above and below your current frequency, storing active frequencies as it goes (with-
out stopping on them even momentarily). These frequencies are stored into a special Smart
Search memory bank, consisting of 31 memories (15 above the current frequency, 15 be-
low the current frequency, plus the current frequency itself). All channels where activity is
present will be loaded into the Smart Search memories. The search will stop after one
sweep in each direction, whether or not all 31 memories are filled.
Storing Smart Search Memories
1. Set the radio to the VFO mode. Be sure that you have the Squelch adjusted properly (so
that band noise is quieted).
2. Press the top panel / key to select “SSCH”.
3. Press the key to initiate upward scanning.
4. As active channels are detected, they will automatically be
stored into the Smart Search memory bank without causing the sweep to halt.
If you want to change direction of the Smart Search while it is underway, rotate the
DIAL knob one click in the opposite direction (in this case, one click counter-clock-
wise). You will see the scanner reverse direction and Smart Search down in frequency.
5. The Smart Search scan will eventually terminate, and the LCD will revert to Smart
Search Memory Channel “<C>”.
32

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Yaesu FTM-10R wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info