18181
104
Zoom out
Zoom in
Vorherige Seite
1/106
Nächste Seite
E-1
Required specifications of the HDD
Interface .................................................................... IDE/ATA type
Data Transfer Mode ........................................ PIO mode 0 to 4 and
Multi-word DMA mode 0 to 2 compatible
Size ............................................................................. 3.5-inch type
Capacity ..................................................................... 20 to 137 GB
Installation procedures
Before installation
Turn off the power of this unit and unplug the AC power
cable from the wall outlet.
Disconnect all the connections.
Set the HDD to SLAVE (see description below).
MASTER or SLAVE setting on the HDD
It is necessary to set the HDD to MASTER or SLAVE when
connecting the HDD to the component you plan to use. This
unit is designed to operate HDD when it is set to SLAVE.
Usually, setting procedure is written on the HDD itself.
INSTALLING THE HDD
There are some models that do not have a built-in hard disk drive (HDD) depending on the sales location. Please purchase a commercially
available HDD for internal use and install it on this unit correctly, referring to the instruction below.
1. Loosen the two fixing screws on the HDD slot door
and open the HDD slot door.
2. Pull out the HDD tray.
Be careful not to hook the IDE cable and the power cable
over the HDD tray.
Do not apply the excessive force on the HDD tray.
3. Place the HDD on the HDD tray.
HDD is a very sensitive device. Be careful not to give any
shock to it.
4. Tighten the four fixing screws.
Fixing screws
Example: When setting the WD800AB model
The HDD is set to slave by setting the plastic shunt at the second
position from right of the jumper switch.
Plastic shunt
Fixing screws
(Screws are on the opposite side)
Example: When setting the ST340810A model
The HDD is set to slave by setting no plastic shunt at any
position of the jumper switch.
999_HD1300(HDD)_GB 02.6.28, 9:19 AM2
104

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Yamaha CDRHD1300E wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Yamaha CDRHD1300E

Yamaha CDRHD1300E Bedienungsanleitung - Deutsch - 100 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info