Bedienungsanleitung Yamaha EMX 512 (Seite 31 von 36) (Englisch)

484104

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

Troubleshooting

EMX512SC/EMX312SC/EMX212S

Troubleshooting

■

Power doesn’t come on.

❑

Be sure that you are using the supplied power cord, and that it is correctly

connected to the AC IN connector and plugged into a working power out-

let.

■

Power suddenly went off.

❑

Check whether the vents at the sides and rear of the unit are blocked.

The EMX unit may overheat if the vents are blocked. If the unit overheats,

the power may automatically go off. Wait for the unit to cool down, and

then turn the power back on.

■

Sound suddenly

stopped.

❑

Check whether the vents at the sides and rear of the unit are blocked.

The EMX unit may overheat if the vents are blocked. If the unit overheats,

it may cut off the output to the internal amp until things cool down.

■

No sound.

❑

Are microphones, external devices, and speakers connected correctly?

❑

Are the channel LEVEL knobs and the two MASTER knobs set to appro-

priate levels?

❑

Is the POWER AMP switch set correctly?

When outputting a stereo signal, set it to the up (MAIN L/R) position.

❑

Check that the speaker cables are not shorted.

❑

If the above checks do not identify the problem, call Yamaha for service.

(Refer to the end of this manual for a list of Yamaha dealers.)

■

Sound is faint, distorted,

or noisy.

❑

Check that the channel LEVEL knobs and the two MASTER knobs are set

appropriately.

❑

Check that the LINE/MIC switches on channels 1 to 4 are set correctly.

❑

On channels 1 to 4, be sure that you have not connected to both INPUT A

and INPUT B. On each of these channels you may use one input or the

other, but not both.

❑

Is the input signal from the connected device set to an appropriate level?

■

An FCL lamp comes

even though there is no

howling on the channel.

❑

Input of a continuous sound (from a CD player or other such source) may

cause the lamp to come on even in the absence of howling.

■

Can’t hear the internal

digital effect.

❑

Check that the EFFECT knob on each channel is correctly adjusted.

❑

Be sure that the internal effector’s ON switch is turned on.

❑

Be sure that the EFFECT RETURN knobs in the MAIN and MONITOR

sections are correctly adjusted.

■

The sound from the

speakers seems dull.

I want a more forceful

sound.

❑

Try turning on the YS Processing switch.

❑

Adjust the equalizers (HIGH, MID, and LOW knobs) on each channel.

❑

Adjust the graphic equalizers.

■

I want spoken words to

be heard more clearly.

❑

Be sure that the YS Processing switch is turned off.

❑

Adjusting the equalizers (HIGH, MID, and LOW knobs) on each channel.

❑

Adjusting the graphic equalizers.

■

I want to listen to moni-

tor output.

❑

Connected a powered speaker to the MONITOR OUT jack. Then adjust

the MONITOR OUT signal by adjusting the channel MONITOR knobs and

the MONITOR section’s MASTER knob.

❑

If you want to send the monitor signal to SPEAKERS jacks B1 and B2, set

the POWER AMP switch to the down position (to MAIN(L+R) / MON).

Note that in this case the B jacks will output the monitor signal, and the A

jacks will output a mix of the MAIN L and MAIN R signals.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha EMX 512 Seite 31

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info