555597
2
Zoom out
Zoom in
Vorherige Seite
1/2
Nächste Seite
CENTER
+
REAR
CONNECTIONS TO YOUR AMPLIFIER
Leave the short
bars in place
when connecting.
Short bar
<Bi-Wiring Connections><Standard Connections>
This speaker system is capable of standard connections and bi-wiring connections. Before making connections, make sure that
the amplifier is switched off.
+
Remove the short
bars before
connecting.
Connections
Connect the screw-type input terminals at the rear of the speaker
to the speaker output terminals of your amplifier with the speaker
cables.
Connect the (+) terminals on both the amplifier and the speaker
using one side of the cable. Connect the (–) terminals on both
components using the other side of the cable.
Connect the speaker to the rear center terminals of your
amplifier, making sure not to reverse the polarity (+, –). If this
speaker is connected with reversed polarity, the sound will be
unnatural and lack bass.
Procedure:
Loosen the terminal knob.
Remove approx. 10 mm (3/8”) insulation from the speaker
cable and insert the bare wire end properly into the terminal
hole.
Tighten the knob.
Test the security of the connections by tugging lightly on the
cable at the terminal.
Note
Do not let the bare speaker wires touch each other as this
could damage the speaker and/or the amplifier.
Rear center speaker
Amplifier or
Receiver
CENTER
+
REAR
Woofer terminals
Rear center speaker
Amplifier or
Receiver
Loosen
Tighten
Tweeter terminals
+
Bi-Wiring Connections
This speaker system is capable of bi-wiring connections. To
connect the speaker to the output terminals of the amplifier, two
pairs of cables for each of woofer and tweeter are used instead of
standard connections. This type of connection decreases the
modulation distortion caused by electric resistance of the cables
and driving current of the speakers. Consequently, purer sound
quality can be expected.
To utilize bi-wiring connections, remove the short bars from the
terminals first, and then connect the woofer and tweeter to the
amplifier separately using two pairs of cables.
Note
For bi-wiring connections, use the same type of cable for both
the woofer and tweeter, making sure to match the polarity.
2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Yamaha NS-100S wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info