417636
4
Zoom out
Zoom in
Vorherige Seite
1/6
Nächste Seite
4
++–
SPEAKERS
L
R
SPEAKERS
A
B
L
R
++–
SPEAKERS
A
B
L
R
+
+
CONNECTIONS TO YOUR AMPLIFIER
<Standard Connections>
<Bi-Wiring Connections>
This speaker system is capable of standard connections and bi-wiring connections. Before making connections, make sure
that the amplifier is switched off.
Speakers output
terminals of the
amplifier
Connections
Connect the screw-type input terminals at the rear of the
speakers to the speaker output terminals of your amplifier
with the speaker cables.
Connect the (+) terminals on both the amplifier and the
speakers using one side of the cable. Connect the (–)
terminals on both components using the other side of the
cable.
Connect one speaker to the left (marked L) terminals of your
amplifier, and another speaker to the right (marked R)
terminals, making sure not to reverse the polarity (+, –). If
one speaker is connected with reversed polarity, the sound
will be unnatural and lack bass.
Procedure:
Loosen the terminal knob.
Remove approx. 10 mm (3/8”) insulation from the speaker
cable and insert the bare wire end properly into the
terminal hole.
Tighten the knob.
Test the security of the connection by tugging lightly on the
cable at the terminal.
Note
Do not let the bare speaker wires touch each other as this
could damage the speaker and/or the amplifier.
Bi-Wiring Connections
This speaker system is capable of bi-wiring connections. To
connect the speakers to the output terminals of the amplifier,
two pairs of cables for each of woofer and tweeter are used
instead of standard connections. This type of connection
decreases the modulation distortion caused by electric
resistance of the cables and driving current of the speakers.
Consequently, purer sound quality can be expected.
To utilize bi-wiring connections, remove the short bars from the
terminals first, and then connect the woofer and tweeter to the
amplifier separately using two pairs of cables.
Note
For bi-wiring connections, use the same type of cable for
both the woofer and tweeter, making sure to match the
polarity.
Leave the short
bars in place
when connecting.
Short bar
Amplifier or
Receiver
+
Loosen
Tighten
Speaker
(L)
Speaker
(R)
Amplifier or
Receiver
Amplifier or
Receiver
Speaker
(L)
Speaker
(R)
Speaker
(L)
Speaker
(R)
+
Remove the short
bars before
connecting.
Woofer terminals
Tweeter terminals
Both SPEAKERS A and B
should be selected.
4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Yamaha ns 300 x wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info