Bedienungsanleitung Yamaha pianocraft dvd-e600 (Seite 24 von 27) (Englisch)

157226

Zoom out

Zoom in

Vorherige Seite

1/27

Nächste Seite

Refer to the chart below when this unit does not function properly. If the problem you are experiencing is not listed

below or if the instruction below does not help, set this unit to the standby mode, disconnect the power cord, and

contact the nearest authorized YAMAHA dealer or service center.

Problem Solution

No power – Check if the AC power cord is properly connected.

No picture – Check if the TV is switched on.

– Check the video connection.

– If you did not use Progressive Scan connections (using the Y PB PR jacks

on the DVD Player) and you do not have a picture at the TV, please follow

the steps below to turn off Progressive Scan;

1. Press / (OPEN/CLOSE) to open the disc tray.

2. Press 1.

3. Then press MUTE to deactivate the Progressive. The DVD Player will

reset itself to Component/Interlaced video.

Distorted picture – The disc is badly scratched or dirty.

– Sometimes a small amount of picture distortion may appear.

This is not a malfunction.

Completely distorted picture or black/white

picture with DVD or Video CD

– Make sure the PAL/NTSC setting at the DVD player matches the video

signal of your television. (See PAL/NTSC CONVERSION)

No sound or distorted sound – Adjust the volume.

– Check that the speakers are connected correctly.

No audio at digital output – Check the digital connections.

– Check if your receiver can decode MPEG-2 and if not, please make sure

the digital output is set to PCM.

– Check if the audio format of the selected audio language matches your

receiver capabilities.

Disc can’t be played – The DVD+R/DVD+RW/DVD-R/DVD-RW/CD-R/CD-RW must be finalized.

– Ensure the disc label is facing up.

– Check if the disc is defective by trying another disc.

– If you have recorded this particular Picture CD or MP3 CD yourself, please

ensure that your disc contains at least about 6~10 pictures or 3~5MP3

music tracks before using it with the player.

No return to start-up screen when disc is

removed

– Reset the unit by switching the player off, then on again.

The player does not respond to the remote

control

– Aim the remote control directly at the sensor on the front of the player.

– Reduce the distance to the player.

– Replace the batteries in the remote control.

– Insert the batteries with their polarities (+/– signs) as indicated.

Buttons do not work – In order to completely reset the player, unplug the AC cord from the AC

outlet.

Player does not respond to some operating

commands during playback

– Operations may not be permitted by the disc. Refer to the instructions of the

disc.

DVD Video player cannot read CDs/DVDs – Use a commonly available cleaning CD/DVD to clean the lens before

sending the DVD Video player for repair.

Cannot record MP3 – SCMS copy protected discs cannot be recorded digitally. Try recording by

analog jacks.

Troubleshooting

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yamaha pianocraft dvd-e600 Seite 24

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info