Bedienungsanleitung Yarvik Tab310 (Seite 3 von 20) (Englisch)

466406

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

2.5 Power-on/off

1. Power on: When the battery can provide sufcient power, you can press the key Power and

hold on for two seconds to power on the Tablet. At the time, the Tablet may vibrate. After the

power-on process, the system will enter the screen-locking interface. You can slide rightward

the unlocking icon to enter the main interface.

2. Power off: First press and hold the key Power for 4 seconds, and the system will pop up the

interface for power-off conrmation. You can click the red icon at the right and power off the

Tablet, or click the key Cancel at the lower right corner to cancel the operation. In the latter

case, the system will return to the Power-Off interface.

3. Sleeping mode: Press the power switch for one second, and the system will enter the sleeping

mode, in which the LCD screen will turn black. In this mode, you can press any key to wake up

the system. Once waken up, the system enters the screen-locking interface. To save energy,

if the electricity is insufcient in the sleeping mode, the system can power off itself after it is

automatically powered on.

2.6 Vibration

Power-on/off vibration:

Click the setup icon

the shortcut bar, and select settings for the voice and display mode.

Then select or deselect the check box behind the “Haptic feedback”

2.7 Turning interface

The interface can be turned at times when the direction of the Tablet changes.

2.8 External network cable and USB stick

External network cable

Connect the port replicator to the Tablet and insert the network cable into the port of Ethernet.

Once logged in, the system will automatically obtain an IP address for network access. Network

access can also be realized through manual setups.

USB stick:

Connect the port replicator to the Tablet and insert the USB stick into the USB port. Once it is

properly connected, you can save and copy contents between the USB stick and the Tablet.

2.9 Network connection

Cable network:

After you insert the network cable into the port designed for Ethernet on the port replicator connected

to the Tablet, the icon “ETH” will appear on status bar at the top of the screen. Then the Tablet will

obtain the IP address automatically to access to the network. Network access can also be realized

through manual setups.

Wireless network:

1 Move leftward the WI-FI switch at the upper right part of the Tablet to be in the ON state;

2 Select the icon “setup” under the shortcut bar on the desktop;

3 Select “wireless network” in the setup menu;

4 Open WI-FI through the check box behind it;

5 Select “WI-FI setup” to set the WI-FI network;

6. All APs found by the Tablet will be listed. You can click the AP name to be connected;

7 If the connection is successful before the AP, the information of AP will be saved. To start connect-

ing, select “connect” in the popped-up window. To eliminate the AP information, select “forget”;

English

TAB310_manual_syl.indd 4 20-06-11 18:46

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Yarvik Tab310 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yarvik Tab310

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info