Bedienungsanleitung Yuneec Tornado H920 Plus (Seite 36 von 40) (Englisch)

669702

Zoom out

Zoom in

Vorherige Seite

1/40

Nächste Seite

BINDING (SINGLE MODE)

The H920 PLUS and ST16 have already been bound before leaving our factory, so

there is no need to bind the aircraft to the ST16 if no gimbal is used. If the CGO4

gimbal is to be attached to the aircraft, only CGO4 needs to be bound to the ST16. If

both the CGO4 gimbal and the aircraft need to be bound to the ST16, the steps below

can be followed:

CAMERA CONTROLS (SINGLE MODE)

STEP 1) Power on the ST 16 Ground Station and power on the on the H920 PLUS

aircraft. Wait for the initialization to completes.

STEP

2) Tilt the H920 PLUS toward the nose twice (45°) until the Main LED indicator

blinks orange rapidly.

STEP

3) On the ST16, open the system settings

menu and tap the 'Refresh' button.

STEP

4) Select the 'SR24_XXXXX' receiver listed

in the column under 'Model', and YUNXXXXX

Wi-Fi listed in the column under 'camera' on the

ST16 Ground Station. Select 'Bind' and then

enter the password '1234567890' to connect to

Wi-Fi. Choose 'OK' after the connection has

been established. Select CGO4 to complete the

camera binding process.

STEP

5) Tap the 'Back' button to return to the

main screen and two long beeps confirm the

connection. The camera video will display on the ST16 screen.

NOTICE:

Copying a model may also be used to bind a new aircraft. Long press the

original model icon and choose 'Copy' from the sub-menu. Repeat the above steps.

NOTICE:

If an error message is displayed in camera mode, tap “OK” to enter camera

mode. Select CGO4, and select the return button to return to the control interface.

GIMBAL CAMERA TILT CONTROL

There is a gimbal tilt mode switch on ST16 labelled “S1.” When the switch is in

up/middle position, the CGO4 (or other gimbal system) gimbal camera is in Angle

Mode. Use the slider (C) on the under-left side of the ST16 to set the tilt position of

the gimbal camera. When the S1 is in the bottom position, the gimbal camera is in

Velocity Mode. When the slider (C) is in the middle position, it means the velocity rate

is 0 for the CGO4, disabling tilt. When the slider (C) is above the middle position, the

CGO4 will enable upward tilt/angle. When the slider (C) is below the middle position,

the CGO4 will enable downward tilt. The distance between the slider(C) and the

middle position determines the tilt speed, the further distance, the faster the tilt

speed.

CAUTION:

Video recording must be stopped to take still photos. It will take

approximately 1-2 seconds to capture a still photo and before another image may be

taken.

CAUTION:

ALWAYS stop recording video before powering down H920 PLUS to avoid

loss of video data.

NOTICE:

Only when in Velocity mode may the gimbal camera be tilted upwards

(Maximum angle-15º).

BINDING (SINGLE MODE)

The H920 PLUS and ST16 have already been bound before leaving our factory, so there is no need to

bind the aircraft to the ST16 if no gimbal is used. If the CGO4 gimbal is to be attached to the aircraft,

only CGO4 needs to be bound to the ST16. If both the CGO4 gimbal and the aircraft need to be bound

to the ST16, the steps below can be followed:

STEP 1) Power on the ST 16 Ground Station and power on the on the H920 PLUS aircraft. Wait for

the initialization to completes.

STEP 2) Tilt the H920 PLUS toward the nose twice (45°) until the Main LED indicator blinks orange

rapidly.

STEP 3) On the ST16, open the system settings menu and tap the

‚Refresh‘ button.

STEP 4) Select the ‚SR24_XXXXX‘ receiver listed in the column

under ‚Model‘, and YUNXXXXX Wi-Fi listed in the column under

‚camera‘ on the ST16 Ground Station. Select ‚Bind‘ and then

enter the password ‚1234567890‘ to connect to Wi-Fi.

Choose ‚OK‘ after the connection has been established.

Select CGO4 to complete the camera binding process.

STEP 5) Tap the ‚Back‘ button to return to the main

screen and two long beeps conrm the connection. The camera video will display on the ST16 screen.

NOTICE: Copying a model may also be used to bind a new aircraft. Long press the original model icon

and choose ‚Copy‘ from the sub-menu. Repeat the above steps.

NOTICE: If an error message is displayed in camera mode, tap “OK” to enter camera mode. Select

CGO4, and select the return button to return to the control interface.

CAMERA CONTROLS (SINGLE MODE)

GIMBAL CAMERA TILT CONTROL

There is a gimbal tilt mode switch on ST16 labelled “S1.” When the switch is in up/middle position, the

CGO4 (or other gimbal system) gimbal camera is in Angle Mode. Use the slider (C) on the under-left

side of the ST16 to set the tilt position of the gimbal camera. When the S1 is in the bottom position, the

gimbal camera is in Velocity Mode. When the slider (C) is in the middle position, it means the velocity

rate is 0 for the CGO4, disabling tilt. When the slider (C) is above the middle position, the CGO4 will

enable upward tilt/angle. When the slider (C) is below the middle position, the CGO4 will enable down-

ward tilt. The distance between the slider(C) and the middle position determines the tilt speed, the

further distance, the faster the tilt speed.

CAUTION: Video recording must be stopped to take still photos. It will take approximately 1-2 seconds

to capture a still photo and before another image may be taken.

CAUTION: ALWAYS stop recording video before powering down H920 PLUS to avoid loss of video

data.

NOTICE: Only when in Velocity mode may the gimbal camera be tilted upwards (Maximum angle-15º).

Yuneec Tornado H920 Plus Seite 36

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Yuneec Tornado H920 Plus

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info