Bedienungsanleitung Zanussi ZI457 (Seite 15 von 19) (Englisch)

22313

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

Certain problems are due to lack of simple maintenance

or oversights and can be solved easily without having to

call out an engineer.

The machine will not start

■ The door has not been properly closed.

■ The plug is not properly inserted in the power socket.

■ There is no current at the socket. Check the fuse.

This dishwasher may display a fault code in the pilot

lights of the programmes which will assist you in iden-

tifying the fault.

If the pilot light ON//OFF is not illuminated and one of

the programme’s pilot light is flashing please carry out

the following checks.

If the pilot light of the RINSE AND HOLD

programme is flashing

The dishwasher will not fill with water

■ The water tap is closed.

Open the tap. Switch off the dishwasher; switch it

back on and start the wash programme. If the

alarm reappears, call the Service Centre.

■ Mains water supply cut off.

Wait for the supply to be restored.

Switch off the dishwasher; switch it back on and

start the wash programme. If the alarm reappears,

call the Service Centre.

■ Water feed pipe bent or squashed.

Reposition the pipe (see instructions for connection

to the water supply).

Switch off the dishwasher; switch it back on and

start the wash programme. If the alarm reappears,

call the Service Centre.

■ Filter in the water feed pipe clogged.

Close the water tap, unscrew the water feed pipe

and thoroughly clean the filter. Screw the pipe back

on and open the water tap.

Switch off the dishwasher; switch it back on and

start the wash programme. If the alarm reappears,

call the Service Centre.

If the pilot light of the INTENSIVE

programme is flashing

■ The filters are clogged.

Clean the filters (see Maintenance section).

Switch off the dishwasher; switch it back on and

start the wash programme. If the alarm reappears

call the Service Centre.

if the pilot light of the QUICK programme

is flashing

The dishwasher does not empty out water

■ The discharge pipe is bent.

Eliminate the bend ( see instructions for connection

to the drain).

Switch off the dishwasher; switch it back on and

start the wash programme. If the alarm reappears,

call the Service Centre.

■ The sink drain is blocked.

Unblock the sink drain pipe.

Switch off the dishwasher; switch it back on and

start the wash programme. If the alarm reappears,

call the Service Centre.

■ The discharge pipe extension is not correct.

Carefully follow the instructions for “Connection to

the drain”.

Switch off the dishwasher; switch it back on and

start the wash programme. If the alarm reappears,

call the Service Centre.

■ The wall drain connection has no breather.

Consult a qualified engineer.

If the pilot light of the NORMAL o

ECONOMY programme is flashing

■ General.

Switch off the dishwasher; switch it back on and

start the wash programme. If the alarm reappears,

call the Service Centre.

SERVICING

PRA10GB

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zanussi ZI457 Seite 15

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Zanussi ZI457

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info