Bedienungsanleitung Zehnder AS 07 (Seite 7 von 8) (Deutsch)

483706

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

The normal installation is like the above

Condition 1: Powering the Antenna by STB or Digital TV

Step 1.Take out the main unit AS 07

Step 2.Take out the multi-directional base. Fixed it on the wooden pole or at a wall (as figure, please

check the follow paragraph for information)

Step 3.fix the main unit to the multi-directional base

Step 4.Take the Coaxial(IEC male to F female) Cable connect the IEC Male end to the IEC Female

End of your Set Top Box or TV Set and F female the F-Female End of the AS 07.

Please note: all the connection should be fixed. It is recommended that you should had a

water-drop loop at the end of cable before entering your home.)

Step 5Adjust the orientation of AS 07. (Normally speaking, the signal is horizontal direction.)

Condition 2: Powering the antenna by AC adaptor( in cases that there is no DC

power out from the STB or Digital TV, you need to do this installation)

Tips for correct Antenna Adjustment

When you finished the installation, you can use your Set Top Box to check the signal strength

and quality. If the quality is not good enough to have good picture, you can move the antenna

to get the best reception position, when you find the best position , please fixed it. If not, you

can change the reception direction by adjust the main unit

Indoor /Outdoor Wall Mounted installation

If you want to hook this unit onto a brick wall or RC

wall, please follow the steps bellow

Before the following step, please make sure that you

have enough protection when you try to drill on the

wall.

Step 1. Mark the fixing position with pencil or another

pen( please use the multi-directional base to

mark the position)

Step 2.Take the electric drill, using 5.8mm drill bit( please note , when you use the electric drill, you

should better to wear the protection device. And the drill bit should be fixed, otherwise there

will be a serious injuring happened when the bit is broken or loose). Drill the depth to 35mm.

Then clean the hole.

Please note , if you want to install On a wooden wall , you don´t need to drill holes

before!

Step 3.Take out the plastic pole, using hammer to ham it into the hole made by step1

Step 4.Take out the screws attached, using screw driver to fix these screws through the base and fix it

on the wall.

Step 5. Fix the main unit on the multi-directional base

Step 6.Take the Coaxial(IEC male to IEC female) Cable connect the IEC Male end to the IEC Female

End of your Set Top Box or TV Set and IEC female to “Receiver” on power inserter. Take

another coaxial (F male to IEC male) cable, connect the F-male End to the F-Female End of the

AS 07 and IEC male to “Antenna” on Power inserter. Please note: all the connection should be

fixed. It is recommended that you should had a water-drop loop at the end of cable before

entering your home. (if your installation is outdoor)

Step 7.Take out the AC-DC Adaptor, connect the barrel end to the DC input of Power inserter, AC end

to the AC Outlet. Please note use only supplied AC adaptor

Step 8.Adjust the orientation of AS 07. (Normally speaking, the signal is horizontal direction.)

Final

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zehnder AS 07 Seite 7

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info