Bedienungsanleitung Zelmer 23Z010 (Seite 53 von 56) (Englisch, Polnisch)

538919

Zoom out

Zoom in

Vorherige Seite

1/56

Nächste Seite

AIR CONDITIONER FUNCTIONS

The air conditioner has three functions: cool, dry, and fan ventilation.

Introduction

Make sure the water container ● (D) is properly installed. Otherwise the appliance will not operate.

Plug the appliance only to a grounded AC socket connected to a protection circuit. ●

Do not connect the appliance to a multiple socket outlet which is also being used for other electrical appliances. ●

Insert the plug into a power source and Press the ON/OFF ● (8) button on the control panel for the appliance to start operating.

Cooling operation

Press the MODE button – (10) several times until the “COOL” indicator light comes on: cooling operation (10c).

Press the “TEMP SETTING” buttons – (7) and (9) to select the desired room temperature. The temperature can be set within a range of

17°C-30°C/62°F-88°F.

Press the “FAN SPEED” button – (11) to select the fan speed: low (11a), med (11b) or high (11c).

NOTE: In order to improve the cooling efciency follow the instructions below:

1. Draw the curtains if the room is directly exposed to the sun.

2. Do not place the air conditioner near other heat sources.

Dehumidifying operation

Press the MODE button – (10) several times until the “DRY” indicator light comes on: dehumidifying operation (10b).

During the dehumidifying mode the fan speed and the temperature cannot be adjusted. The fan motor operates at high speed. –

Keep windows and doors closed for best dehumidifying effect. –

Do not put the duct to the window. –

CAUTION: If the compressor cycle is interrupted during the cooling or dehumidifying mode (appliance unplugged, power failure)

and reinstated immediately thereafter, a compressor protection circuit is automatically self-affected. The compressor cannot oper-

ate during a compressor protection condition. It may take about 3 minutes before the protection circuit deactivates (this is a normal

situation).

Ventilation

Press the MODE button – (10) several times until the “FAN” indicator light comes on: ventilation (10a).

Press the “FAN SPEED” button – (11) to select the fan speed: low (11a), med (11b) or high (11c).

The temperature cannot be adjusted. –

Do not put the duct to the window. –

AUTOMATIC SWITCH ON / SWITCH OFF

Timer operation (setting the on timer)

Press the TIMER ON – (4) button when the appliance is plugged in to a power source.

Press and hold or keep pressing the TIMER ON – (4) button to set the time after which the appliance will automatically switch on. The time

is programmed as: 0,5 - 1,0 - 1,5 - 2,0 - 2,5 - 3,0 - 3,5 - 4,0 - 4,5 - 5,0 - 5,5 - 6,0 - 6,5 - 7,0 - 7,5 - 8,0 - 8,5 - 9,0 - 9,5 - 10 - 11 -12 - 13 - 14

- 15 - 16 - 17 - 18 - 19 - 20 - 21 - 22 - 23 - 24 - 0,0 hours

The starting time is adjustable from 0,0 – 24. –

Timer operation (setting the off timer)

Press the TIMER OFF – (4) button when the appliance is operating.

Press and hold or keep pressing the TIMER OFF – (5) button to set the time after which the appliance will automatically switch off. The

time is programmed as: 0,5 - 1,0 - 1,5 - 2,0 - 2,5 - 3,0 - 3,5 - 4,0 - 4,5 - 5,0 - 5,5 - 6,0 - 6,5 - 7,0 - 7,5 - 8,0 - 8,5 - 9,0 - 9,5 - 10 - 11 12 - 13

- 14 - 15 - 16 - 17 - 18 - 19 - 20 - 21 - 22 - 23 - 24 - 0,0 hours

The switching off time is adjustable from 0,0 – 24. –

WATER DRAINAGE METHODS

There are two possible methods of water drainage available for this appliance – water container drainage or continuous drainage.

Water container drainage

A) During cooling mode

When the water level inside the water container – (D) reaches a predetermined level, the appliance will switch off automatically. The motor

fan will continue to operate.

Carefully remove the water container – (D) and dispose of the water. Replace the water container back to its original position.

B) During the dehumidifying mode

Water will accumulate in the water container – (D). When the water container is full, the Water Full indicator (3) will illuminate and the dehu-

midication process will automatically stop. However, the fan motor will continue to operate (this is a normal situation). Carefully remove

the water container and dispose of the water. Replace the water container back to its original position. The dehumidication process will

automatically resume. It may take 3–5 minutes for the compressor to restart. This is a normal situation.

Continuous drainage

The continuous drainage option can be selected during the cooling and dehumidifying mode. Remove the water container – (D).

Inside, beside the water container you will nd a section of the hose that is plugged at the end. Release the band and remove the plug –

form the end of the hose.

Replace the water container – (D) back to its original position and route the hose through the hole on the bottom of the water container.

Place the other end of the hose directly over the drain area. –

CAUTION: Make sure the drain hose routed through the water container does not interfere with the correct positioning of the water

container. Otherwise the fail-safe switch mechanism will be activated, not allowing the appliance to operate.

Zelmer 23Z010 Seite 53

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info