Bedienungsanleitung Zelmer 32Z012 (Seite 28 von 30) (Englisch, Polnisch)

539094

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

Handling and operation (Fig. B)

Preparation for operation

Before rst usage (or after long storage) wash the jug (9), lid

(8) and feeder opening stopper (7) in hot water with washing-

up liquid, rinse and dry well. Keep your hands away from

cutting blades (14) – they are sharp.

Operation manual

Place the motor housing (10) on dry, rm, and horizontal

surface, near mains supply outlet and out of the reach of

children.

Arrange the supplying cord so that it does not hang from

the table or board and it can not be pulled or dragged by

accident.

Connect the plug into the mains supply outlet.

Place the jug (9) so, that the protrusions at the bottom

part of the jug (9) were tted with the protrusions in top part

of motor housing (10).

After proper assembling of the jug, the blue highlight

shall glow around the control panel (11).

The handle of the blender jug (9) shall be placed on the

right side of the appliance.

Put the ingredients into the jug (9).

Do not ll in over 1500 ml marked on the blender

jug (9). In such case, the content of the jug can lift the lid

(8) when the motor starts up.

Before you use the stand blender, assemble the lid (8)

on the blender jug (9) so, that its protrusion was in line with

the protrusion in the jug.

ATTENTION: Before you insert the lid (8) moisture the

lid gasket with water.

Insert the lid overlay (7) into the inlet in the lid (8) so that

the protrusions of the overlay enter the cuts in the lid inlet

and turn it left or right until it moves.

Do not start the stand blender without the feeder

opening stopper (1), especially, when you use solid

ingredients. They can be thrown out of the opening.

Switch mixing on pressing speed I (2), speed II (5) or

CLEAN/PULSE (6).

Press ON/OFF switch to turn off the appliance.

Operating with speed I or speed II, the appliance is

switched off automatically after 2 minutes.

CLEAN/PULSE function

Pressing CLEAN/PULSE

●

(6) button shall cause short

operation with maximum speed.

Do not operate longer than 3 minutes, otherwise it can

●

get overheated.

If you need to add some new ingredients during blender

●

operation, turn and lift feeder opening stopper (7), feed

the ingredients into the opening, then replace the stopper

again (7) and turn it left or right until it runs.

Make sure, that the ingredients you add, shall not

●

increase the capacity inside the jug exceeding 1500 ml

marking on the jug (9).

ICE function

Check if the stand blender is clean, before you use it for

●

crushing ice. Otherwise wash it thoroughly with clean

water. Any residues of washing agent can inuence the

taste of crushed ice and shall cause that the drink we

add the ice to, shall loose its taste.

In case you want to crush ice, use 6 to 10 ice cubes

●

(max. 2 cm) in given time, and then add 15 ml (1 spoon)

fresh cold water.

Assemble the lid

●

(8) including overlay (7) on the appli-

ance and press ICE switch.

ICE feature operates for 30 seconds, then the appli-

ance switches off automatically.

Do not try to crush the ice without adding some water

into the jug.

Press the lid (8) with one hand during ICE feature is on.

After operation

To switch off the stand blender press and hold ON/OFF

switch for 3 seconds, until the blue highlight around the

control panel (11) is off.

Hold the motor unit

●

(10) with one hand, catch the jug

handle with the other hand and remove it from the motor

unit (10) turning it counter-clockwise.

Remove the lid

●

(8) from the jug (9).

Unplug the appliance from the mains supply outlet when

●

it is not in use.

Cleaning and maintenance (Fig. C)

Clean after operation as soon as possible, to prevent

the pulp accumulation inside the jug (9).

Pour approximately 1 liter of water to the blender jug (9)

and start-up the appliance for approximately 30 seconds and

hold the CLEAN/PULSE button.

Then empty the blender jug (9), turn it upside-down and

dry.

If necessary, clean the jug (9), lid (8), feeder opening

stopper (7) and blades (14) in warm water with wash-up

liquid.

Then rinse it under clean running water and dry.

●

If you left the jug for longer time without cleaning and

●

some particles glued to the jug inner, use nylon brush.

We do not recommend cleaning the jug

●

(9), blades (14),

lid (8) and feeder opening stopper (7) in dish washer.

Aggressive cleaning agents applied in such device can

inuence negative the surface conditions.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zelmer 32Z012 Seite 28

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info