Bedienungsanleitung Zepter PWC-200 - Tuttoluxo 2S (Seite 18 von 22) (Englisch)

657583

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

3 4

9.2 SIMPLY SYSTEM

No need to store up on bags or filters thanks to the SIMPLY SYSTEM

Cleaning the purification tank is all that is required for top TUTTOLUXO 2S

efficiency. At the end of your work, empty the liquid waste of the purification

tank as shown in (Pict. 3). To make this operation easier, the divider inside the

tank can be taken off (Pict. 4) and it is also advisable to remove the nebulizers

(Pict. 5). Rinse tank, divider and nebulisers with abundant hot water and neutral

detergent until all residues and stains on the tank walls have been removed.

WARNING!

We strongly advise, after aspirating liquids or solids, to rinse the water bucket

inside and any accessory used, by emptying the tank and aspirating 1 litre of

cold, clean tap water, repeat this twice. Also, please do not leave any aspirated

liquid inside the tank, to prevent the formation of limescale or moulds, and

consequently bad odours.

WARNING!

When you take off the divider, make sure that it is put back correctly into the proper

guides with its curved side facing forwards and upwards and that it touches the

bottom (otherwise it won’t slide in). Please be careful, these are delicate pieces.

In case one gets broken or lost, immediately ask for a spare part from your Zepter

Service Centre. Do not use the TUTTOLUXO 2S without it. Allow all pieces to dry

or dry them yourself before replacing them in the machine and closing the cover.

Moisture left inside could create mildew and unpleasant odours.

REPLACEMENT OF FILTERS:

Floater Filter (PWC-700-4): Replace yearly or earlier according to condition.

Air Intake Filter (PWC-700-2): Replace yearly or earlier according to condition.

Polyester Filter (PWC-700-1): Replace yearly or earlier according to condition.

Motor Intake Filter (PWC-700-3): Replace yearly or earlier according to condition.

Hepa Filter (PWC-700-5): Replace every 6-12 months.

To inspect the filter, proceed as for replacing the Polyester Filter

1) Remove the grilled cover on the back of the TUTTOLUXO 2S.

The HEPA filter is fitted inside. Place the grilled cover on the floor and

extract the filter as shown.

2) Check the filter state; if there are traces of dust or dirt, replace it.

3) Put the new HEPA filter into place and reassemble the cover,

making sure to properly fit the grilled cover hooks onto the slits on the

appliance body. Once the grilled cover is in place, rotate it upwards for the

final fixing with the stopping tongue.

After some periods of use, should the HEPA filter be torn or damaged, it should

be replaced with a new one from a Zepter Service Centre.

TANK LID WITH FLOAT

Also check efficacy of the Safety Float located on the tank lid. If encrusted

with dirt or mould, this may not function correctly. Check that the float can

move freely within its cage. Rinse the lid with plenty of hot water and neutral

detergent.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zepter PWC-200 - Tuttoluxo 2S Seite 18

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info