Bedienungsanleitung Zoom MRS-802 (Seite 181 von 184) (Englisch)

533782

181

Zoom out

Zoom in

Vorherige Seite

1/184

Nächste Seite

Creating a CD using the disc-at-once method

ZOOM MRS-802 Ver 2.0

●

To switch the V-take for the master track

Press the [EXIT] key repeatedly to return to the main

screen. Load the project for which you want to switch

the V-take, and select the V-take for the master track.

Then return to the album screen.

11.

When you have stored all desired projects

in the album, press the [ENTER] key twice.

The display indication changes as follows.

HINT

If you press the [ENTER] key once more, the indication “CD

xx Trk BURN?” (where xx is the number of tracks) appears on

the display. You can check the total number of tracks that will

be written to the disc from this screen.

12.

To carry out the write process, press the

[ENTER] key once more.

By pressing the [EXIT] key instead of the [ENTER] key,

you can cancel the operation and back up one step at a

time. When you start the write procedure, the display

shows “wait...” for track-at-once or “init...” for disc-at-

once. The counter indicates the progress status of the

write process.

When the write process is completed, the disc is ejected

automatically, and the message “ALBUM NEXT?”

appears on the screen. To write another disc with the

same content, insert a blank CD-R/RW disc or a CD-RW

disc which has been completely erased, and press the

[ENTER] key. To terminate the process, press the [EXIT]

key.

13.

To return to the main screen, press the

[EXIT] key several times.

When you create an audio CD using the disc-at-once

method, marker information included in the project can

be used to generate PQ subcode information (specifying

track start/stop position and other items) to split up a

single project into multiple tracks. Marker-based track

separation can be enabled or disabled for each project.

For example, when a project contains a number of songs

that were recorded live, you can set a mark at the

beginning of each song, so that these will be recorded as

different tracks on the CD. This will enable easy

searching and jumping between tracks.

NOTE

To use the marker-based track separation function, at least

two marks (including the project start mark 00) must be set.

Load the project that you want to split into

multiple tracks, and set marks at the points

where the tracks should be separated.

Marker-based track separation can only be enabled or

disabled for the entire project. Delete any unnecessary

marks beforehand.

Perform steps 1 - 6 of “Creating an audio

CD by album”, select the disc-at-once

(DAO) write method, and bring up the

album screen.

Use the cursor left/right keys and the dial to

Use the cursor left/right keys to select a

project that is to be divided into multiple

tracks.

Press the [MARK] key in the control

section.

Marks contained in this project will be used as PQ

subcodes. The indication “PQ” is shown at the top right

of the display.

By pressing the [MARK] key again, you can return to the

ALBUM

SURE?

Using the marker function to

separate tracks

END OF

PROJECT

0 0 0

MRS802v2(E).fm 9 ページ２００４年５月２７日　木曜日　午後５時５９分

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Zoom MRS-802 Seite 181

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Zoom MRS-802

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info