Bedienungsanleitung AEG SB2E 760 R (Seite 4 von 84) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

463191

Zoom out

Zoom in

Vorherige Seite

1/84

Nächste Seite

ENGLISH

SBE 600 R, SB2E 680 R, SB2-700, SB2E 700 R, SB2E 700 RS, SB2E 705 PLUS, SB2E 750 R, SB2E 760 R

Connect only to a single-phase AC current supply and only to the mains voltage

specified on the rating plate. Connection to sockets without earth protection is

possible as the appliance features protective insulation to DIN 57 740/ VDE 0740

and CEE 20. Radio suppression complies with the European standard EN 55014.

When fitting the plug, make sure that the brown (live) wire of this appliance is

connected to the plug terminal marked L or coloured red, and the blue (neutral) wire

of this appliance is connected to the plug terminal marked N or coloured black.

Under no circumstances must the wires of this appliance be connected to the earth

terminal of the plug marked either E, with the earth symbol or coloured green or

green/yellow.

The electronic drill/screwdriver can be universally used for drilling, percussion drilling,

screwdriving and cutting screw threads.

Do not use this product in another way as stated for normal use.

Always disconnect the plug from the socket before carrying out any work on the

machine.

1. Usually, the chuck can be removed by

hand: steady the drill spindle with a fork

wrench and unscrew the chuck by turning

it anti–clockwise.

2. Should the chuck be stuck on the drill

spindle, fit another fork wrench to the

chuck and the drill spindle (see illustration)

or fix an Allen key in the chuck.

If necessary, hit the key shaft lightly with a

plastic hammer.

3. Mount the chuck in reverse order.

Under high strain in anti–clockwise

operation, the chuck might become loose.

Please use the bit reception to loosen screws in anti–clockwise operation. (not for

SB2–700)

Completely insert the tool shaft into the

open chuck.

Hold the grip and firmly tighten the chuck

by turning the sleeve in the ”GRIP”

direction.

After the clamping jaws have tightened

around the tool shaft, turn the chuck a

further 1/4 in order to let the chucking

power retention engage. Only than can the

tool itself be chucked by vigorously turning the sleeve in the “GRIP” direction (it

engages audibly with a grating noise.)

The chucking power retention is mainly needed for percussion drilling.

When the chuck is opened with a strong jerk as far as it will go, it is possible that it

can’t be closed anymore. Instead, ”grating” can be felt (as if the chuck were

over–tightened). In this case turn the sleeve once more in the ”RELEASE”

direction; now it can be closed again. The chuck is not damaged by this ”grating”.

When percussion drilling in stone the drill bit should be checked for tight seat in the

chuck after first use. If necessary, re–tighten the chuck by hand.

Mains

connection

Use

Keyless chuck

(according to

standard

equipment)

Changing the

keyless drill

chuck

Inserting the tool

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

AEG SB2E 760 R Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info