Bedienungsanleitung Al-ko Elektro-Heckenschere 167 (Seite 22 von 68) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

601528

Zoom out

Zoom in

Vorherige Seite

1/68

Nächste Seite

Using your power hedge trimmer ; Operating and maintenance instructions

ENGLISH 10

.3 Decorative cutting

The trapezoidal cutting pattern shown prevents the

lower hedge area from loosing its foliage due to

lack of light.

Fig.10:

Firstly, cut the hedge to the desired height.

Cuttings can be freed from the hedge by a slight

pendulum action. To achieve a straight cut, a taut

piece of string is positioned in the hedge at cutting

height.

Fig.11:

Cut the hedge from below upwards into a

trapezoidal shape (to 1 m height. narrowed at the

top by approximately 10 cm). This prevents

cuttings falling onto that part of the hedge that has

not yet been cut, which may disrupt further cutting.

Slightly bevel the top edge of the hedge; then cut

back the bottom of the hedge near the ground.

To promote thick new growth on young hedges,

only cut back half of the new shoots.

If the hedge has already grown to the desired

height, young shoots can be cut back completely.

The correct time for cutting hedges is:

Leaves: June and October

Needles: April and August

Fast growing hedges: approx. every 6 weeks

from May onwards.

. Operating and maintenance instructions

The maintenance and the repair of modern

machines as well as their safety-relevant

assemblies require qualified specialised training

and a workshop equipped with special tools and

test equipment. Consequently the manufacturer

recommends that all tasks not described in these

operating instructions be carried out by a

specialised workshop. That specialist has the

required training, experience, and equipment at his

disposal, to provide you with the most cost-

effective solution for such work. He will provide

additional help in word and deed.

.1 Blade

Before hedge trimming and after cleaning, treat the

clean blade with maintenance and treatment oil.

We recommend the "Solo maintenance and

treatment oil"

Please note: Never use grease.

To clean the blade after hedge trimming, we

recommend the use of "SOLO Universal-Reiniger

(Cleaner)" After a short

period of soaking in, the ingrained remains of

cuttings on the blade are soft and solvent. They

can then be removed easily with a cloth.

Check the blade at regular intervals and when

cutters operate unusually or if the blades are

jammed. For this, the engine must be switched off

and the blade must be stopped. Clean all clippings,

brush, etc. from the cutter. Ask your local service

shop immediately to sharpen or replace the blade if

it is blunt or damaged, even if it shows only slight

cracks.

Let your service shop sharpen the blade regularly.

During this service, always clean the guide nuts

after removing the blade.

Fig. 10

Fig. 11

Fig. 12

Fig. 13

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Al-ko Elektro-Heckenschere 167 Seite 22

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info