707374
54
Zoom out
Zoom in
Vorherige Seite
1/58
Nächste Seite
54
5. ALARM CLOCK
5.1 Introduction:
You may program an alarm (wake-up) time in the WS-3400.
In addition, you may add a frost alert (
): when it’s colder than -3°C outside, the alarm will sound 30 minutes
earlier than the time you’ve set.
5.2 Alarm time setup:
1. Press and hold the button at the rear of the indoor unit until the hour display starts ashing and AL
appears in the display.
2. Use / to set the hours, briey press and the minute display starts ashing.
3. Use / to set the minutes and briey press to save the alarm time.
5.3 Alarm function setup:
1. Briey press once or multiple times the button to check or enable/disable the alarm
Only “AL” appears: the time that is shown is the set alarm time but the alarm itself is switched o
“AL” + “ ” appears: the alarm is enabled and the alarm signal will sound at the set alarm time
“AL” + “
” appears: the frost alarm is set
2. Release the button, after several seconds the actual time is displayed again and the alarm status
remains as described above, visible
5.4 Operation:
At the set time the alarm will sound for up to 120 seconds
Press the button to stop the alarm sound beforehand OR press the SNOOZE/LIGHT button on top
of the indoor unit to switch on the snooze functioning; the wake-up alarm will then sound again after
5 minutes.
The alarm is repeated every day until you disable is according to the above instructions.
If you’ve enabled the frost alert and it’s colder than -3°C outside, the alarm will sound 30 minutes earlier
than the time you’ve set. If outside it’s warmer than -3°C, the alarm will sound at the set time.
6. MINIMUM AND MAXIMUM MEASURED VALUES
6.1 Introduction:
The measured minimum and maximum values of the following items are saved.
Indoor and outdoor temperature, humidity indoors and outdoors, feels like temperature, heat index, dew
point and wind chill. And additionally the maximum wind speed and gust.
6.2 To view all maximum and minimum values:
Press in the normal mode on the “MEM” button to view all maximum and minimum values. The maximum
indoor temperature appears. Repeatedly press the “MEM” button for the other items.
6.3 To reset the maximum and minimum values:
While the maximum or minimum value is being displayed, press and hold the “MEM” button for 2 seconds
to delete the saved maximum or minimum value. Repeat this for every item to delete all maximum and
minimum values.
54

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Alecto WS-3400 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info