707374
55
Zoom out
Zoom in
Vorherige Seite
1/58
Nächste Seite
55
7. HISTORY
7.1 Introduction:
The indoor unit of the WS-3400 automatically stores all measurement data of the past 24 hours, allowing
you to view the course over the last 24 hours at any time
7.2 History check:
1. Press the HISTORY button, the last saved measurement data are shown on the display while the upper
part of the display shows the time of the concerned measurement
2. Repeatedly press the HISTORY button to scroll the memory
The history memory saves the data of the indoor and outdoor temperature and humidity, wind speed and
feel like temperature.
7.3 To delete the history:
Press and hold the HISTORY button to delete all data measured up to that point.
8. MAX-MIN ALERT
8.1 Introduction:
You may set an alert for the following measurements for when a maximum or minimum value is being
exceeded:
Indoor temperature max alert
Outdoor temperature min alert
Humidity indoors max alert
Humidity indoors min alert
Outdoor temperature max alert
Outdoor temperature min alert
Humidity outdoors max alert
Humidity outdoors min alert
Wind speed max alert
8.2 To set and activate/deactivate Hi-Lo limits:
1. Press the button to activate the Hi-Lo limit setting.
2. Use the / buttons to select “IN” for the indoor temperature or “OUT” for the outdoor tempera-
ture . Choosing OUT 1, OUT2 or OUT3 has no function.
3. Press once or multiple times the button until the desired display starts ashing, followed by ‘HI AL’ or
‘LO AL’ (where applicable)
4. Use / to set the limit
5. Briey press the button to activate the alert and press the button again to deactivate
6. Press the button again to go to the next function or wait several seconds to automatically end the
setup
8.3 Operation:
As soon as the set limit is exceeded, every 2 seconds a beep tone is emitted for up to 2 minutes. Addi-
tionally the concerned display starts ashing. You may stop the alert signal by briey pressing the or
SNOOZE/LIGHT” button. The display stops ashing automatically as soon as the concerned measurement
value falls within the set limit again (or as soon as you change the limit of disable the alert function for this
measurement).
55

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Alecto WS-3400 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info