Bedienungsanleitung Angelcare AC401de luxe (Seite 11 von 16) (Englisch)

537057

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

Other Functions (continued)

PAGING THE PARENT UNIT

Press the TOP BUTTON of the Nursery Unit to

locate the Parent Unit.

1. PAIRING/PAGING BUTTON

PAGING

PART 4 - FREQUENTLY ASKED QUESTIONS

Q. MY MONITOR KEEPS BEEPING/

ALARMING AS I SET IT UP

A. Your monitor (Nursery Unit) is already

pre-programmed to record movement

(and sound). This means that as soon as

the nursery unit receives mains or battery

power, it will start to record movements

(whether or not the SensorPad is plugged

into the nursery unit.) If no movement is

detected the alarm will sound after 15

seconds and will be signalled by one

short beep (rouse alarm), and then 5

seconds later, loud beeps in rapid

succession. To stop the alarm sounding

turn off the Nursery Unit (using the Power

ON/OFF - left wing), and insert the jack

from the SensorPad (if not already

inserted). Turn on the unit and place your

hand on the sensor pad and tap lightly

(simulating movement from your baby).

As movement is detected the green light

on the Nursery Unit will be ﬂashing,

indicating that the unit is picking up

movement. Now remove your hand from

the sensor pad and stand still until the

green light stops ﬂashing and you will

hear ﬁrst the rouse alarm, which is a

short beep, and then the main alarm.

This shows that your monitor is

working properly.

Q. I DON’T WANT TO MONITOR

MOVEMENT WHILST MY BABY IS IN

THE COT NEXT TO MY BED?

A. It is easy to change any settings on your

monitor, by following the instructions in

the manual.

Your Parent Unit is used to remotely

transmit any changes you wish to make

to your Nursery Unit.

You can reactivate or deactivate

movement or sound as your needs

change.

NOTE: If your monitor is set up to record

movement, please ensure that the cot is

not touching your bed as it could be

picking up your movements instead of

your baby’s.

Q. WHAT DO THE ALARMS SOUND LIKE?

A. MOVEMENT ALARM - Single short beep

followed by rapid loud beeps.

There are a sequence of alarms that you

will hear when the monitor is recording

movement. Should the sensor pad not

detect movement for 15 seconds, then a

‘Rouse’ alarm will sound. This is a single

beep and may wake baby from a deep

sleep. If the sensor pad does not pick up

any movement in the 5 seconds following

the rouse alarm then the main alarm will

sound. This sounds like a rapid

succession of loud beeps that are audible

from a distance.

There is a small loudspeaker on the

nursery unit which emits this sound. Also

the nursery unit transmits this sound to

the parent unit which, if is turned on will

also emit the alarm sound. The parent

unit can also be set up to vibrate as a

means of alarm.

OTHER ALARMS

Out of Range

Replace Batteries

HOLD Function

Temperature Warning

Short low

volume beeps

Soft short

beeps that are

merely a

gentle warning

to remind you

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Angelcare AC401de luxe Seite 11

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Angelcare AC401de luxe

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info