Bedienungsanleitung Atlantic F117 ODYSSEE (Seite 6 von 32) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch, Polnisch)

613618

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

The product you have just purchased has undergone numerous tests and inspections to guarantee the highest quality. We hope it will give you entire

satisfaction.

INSTALLATION OF THE PANEL HEATER

Please read the instructions before starting to install the heater. Disconnect

the power before carrying out any work on the heater. Keep these

instructions even once you have installed your heater.

1) Where to install your heater ?

- This equipment was designed to be installed in a residence. Please ask your

distributor before using it for any other purpose.

The panel heater should be installed according to normal trade practice and in

compliance with legislation in the relevant country (the IEE Wiring Regulations).

- The equipment is class 2 and is protected against splashed water IP

24. The device is to be installed so that switches and other controls cannot

be touched by a person in the bath or shower, except in the UK where IEE

Regulations 701.512.2 and 701.512.3 apply. These allow the use of IP24

rated products and their integral controls in Zone 2 and outside zones.

- Comply with the minimum clearance distances for positioning of the panel

heater.

- If your wall covering is laid on foam, a spacer the same thickness as the

foam must be placed under the panel heater’s support. This ensures there is

free space behind the panel heater to make sure its control settings are not

adversely affected.

- Do not install the panel heater:

c In a draught that might affect adjustment (for example, under a

central mechanical ventilation unit etc...).

c Under a xed mains power socket.

c In zone 1 of bathrooms a.

It is forbiden to install vertical product in horizontal position.

2) How to install the panel heater ?

2-1) Release the appliance’s hook-on bracket 

We recommend that you place the radiant panel at, face down.

Have a straight head screwdriver to hand.

2-2) Fix the hook-on bracket 

Use the wall-mounting bracket as a template for positioning the heater.

Drilling points A

Drilling points B

2-3) Connecting the panel heater

- The appliance should have a 230-240V 50Hz power supply.

- The panel heater must be connected to the mains, either by a 3-wire cable

(Brown= Phase, Blue = Neutral, Black = Pilot wire) by means of a connexion

box.

In humid areas such as bathrooms and kitchens the power socket must be

installed at least 25 cm above the oor.

- The installation should be tted with a double pole break device with a break

of at least 3 mm.

- Connection to earth is prohibited. Do not connect the pilot wire

(black) to earth.

- The heater must be installed by a qualied electrician in accordance with

the local regulations. The heater and the pilot wire (black) must NOT be

connected to earth. If the power cable is damaged, it must be replaced by

the manufacturer or its after-sales service Department or a similary qualied

person to avoid any risk.

If a pilot or piloted panel heater is protected by 30mA differential (e.g.

bathroom) the pilot wire’s power must be protected on this differential

Commands

Received

No current

Complete

altermation

230 V

Négative

Half/altermation

- 115 V

Positive

Half/altermation

+ 115 V

Oscilloscope

Réf/Neutral

Mode

obtained

COMFORT ECO

ANTI-

FREEZE

STOP

HEATING –

LOAD

SHEDDING

2-4) Lock the appliance on the hook-on bracket f

USING THE PANEL HEATER

1) Description of the control unit : 

switch .

Temperature adjustment control knob.

Heating indicator light

2) Fixing the comfort temperature

The comfort temperature is the temperature that you would like while the

room is occupied.

a) Put the 1 switch to

b) A

just the control knob

to the wished position, the heating indicator V1

comes on if the room temperature is below the required temperature.

c) Wait a few hours for the temperature to stabilise.

d) If the setting is satisfactory (if necessary use a thermometer to check),

mark the position for future use.

e) If the setting is not satisfactory, adjust it and start again from point c.

3) Fixing the Eco temperature :

This is the required temperature during periods when the room is

unoccupied. It is recommended that this mode should be used if the room is

unoccupied for more than 2 hours.

a) Set the cursor 1 switch knob to

b) Ajust the control knob 2 to the wished position, the heating light V1

comes on, if the ambient temperature is lower than the instruction of desired

Eco temperature.

c) Wait a few hours until the temperature stabilizes.

d) If the setting is satisfactory (if necessary use a thermometer to check),

mark the position.

If the setting is not satisfactory, adjust it and start again from point c.

Note : When switching n°1 (on the picture) is set on Programming system

(clock symbol) with the PassProgram On/Off, please refer to paragraph n°8.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Atlantic F117 ODYSSEE Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info