Bedienungsanleitung Basetech 350C12 - 1586224 (Seite 6 von 12) (Deutsch, Englisch, Holländisch, Französisch)

738498

Zoom out

Zoom in

Vorherige Seite

1/12

Nächste Seite

c) Enable/disable target laser

The target laser can be switched on and off. When the laser is switched on, the laser symbol

(triangle with radiation symbol) is shown on the display.

• Press and hold the Mode button for 3 seconds, to enter settings mode.

• Release the Mode button again to enter settings mode for the target laser.

• To disable the laser, hold down the trigger (1) until "0" appears in the LCD display. To enable

the laser, hold down the trigger (1) until "1" appears in the LCD display. The laser will

automatically be turned on when you take a measurement.

• The target laser is automatically turned on when you take a measurement as long as the

trigger (1) is kept pressed, if "1" was selected. The measuring process takes place without

turning on the target laser support, if set to "0".

• Press and hold the Mode button for 3 seconds to conrm the setting.

Troubleshooting

Problem Cause Solution

Blank display. The product is switched off. Press the trigger button (1)

to switch the product on.

Battery too weak. Replace the battery.

The low battery

indicator (F) will appear

on the display.

Battery weak. Replace the battery.

No temperature is

measured.

Malfunction. Briey press the trigger

button (1) and start the

measurement process

again.

"Hi" appears on the

display.

The temperature of the

measured object exceeds the

measuring range (> +350 °C).

Observe the measuring

range.

"Lo” appears on the

display.

The temperature of the

measured object is below the

measuring range (<-50 °C).

Observe the measuring

range.

Care and cleaning

• Before cleaning the product, disconnect it from the power supply by removing the battery.

• Do not immerse the product in water.

• Never use aggressive detergents, rubbing alcohol or other chemical solutions, as these may

damage the housing or cause the product to malfunction.

• Remove loose particles from the lens with clean compressed air, and then wipe off any

remaining residue with a ne lens brush. Clean the surface of the lenses using a lens cloth

or a soft, lint-free cloth. The cloth can be moistened with water or a lens cleaning solution

to remove ngerprints and other residues. Do not use a rough, uffy cloth to clean the lens.

Avoid applying too much pressure when cleaning the lens.

• Use a dry, lint-free cloth to clean the product housing.

Disposal

a) Product

Electronic devices are recyclable waste and must not be placed in household waste.

At the end of its service life, dispose of the product in accordance with applicable

regulatory guidelines.

If a battery is inserted, remove it and dispose of it separately from the product.

b) Batteries

You are required by law to return all used batteries (Battery Directive). Batteries

must not be placed in household waste.

Batteries containing hazardous substances are labelled with this symbol to indicate

that disposal in household waste is forbidden. The abbreviations for heavy metals

in batteries are: Cd = Cadmium, Hg = Mercury, Pb = Lead (indicated on the battery,

e.g. below the trash icon on the left).

Used batteries can be returned to local collection points, our stores or battery retailers.

You thus full your statutory obligations and contribute to protection of the environment.

Technical data

Temperature measuring range Accuracy

-50 to -19 °C (-58 to -2.2 °F) ± 5 °C

-20 to 79 °C (-5 to 174.2 °F) ± 4 °C

+80 to +149 °C (+176 to +300.2 °F) ± 3 °C

+150 to +350 °C (+302 to +662 °F) ±(3% of the measured value or +1 °C)

Operating voltage ......................... 9 V/DC block battery (1 included in delivery contents)

Current consumption .................... 30 mA (with display lighting and target laser switched on)

Battery life ..................................... 20 hours (with backlight and target laser)

Standby power consumption ........ 3.3 µA (when switched off)

Temperature display range ........... -50 to +350 °C (-58 to +662 °F)

Resolution .................................... 0.1 °C /°F

Measuring range indicator ............ Temperature too high "Hi"/temperature too low "Lo"

Measurement value xing ............. Yes, measurement values are xed in the display

Switch temperature

units between ............................... °C/°F

Emissivity ...................................... 0.95 xed (non-adjustable)

IR measuring spot size ................. Approx. 12:1 (DS)

Spectrum (IR) ............................... 8 -14 µm

Response time .............................. 1 second

Laser class ................................... 2

Laser output power ....................... < 1 mW

Laser wavelength ......................... 654 nm

LCD display .................................. 23.5 x 24 mm

Display backlight ........................... Yes, (white)

Battery level indicator ................... Yes, with 6.5 V ~ 7.0 V

Automatic power off ...................... after 10 seconds of inactivity

Operating conditions ..................... 0 to +50 °C, 10 – 80 % relative humidity (non-condensing)

Storage conditions ........................ -10 to +60 °C, 10 – 80 % relative humidity

(non-condensing)

Dimensions (L x W x H) ................ 153 x 72 x 42 mm

Weight .......................................... 115 g

This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).

All rights including translation reserved. Reproduction by any method, (e.g. photocopying, microlming, or capture in

electronic data processing systems) requires prior written approval from the editor. Reprinting, also in part, is prohibited.

This publication represent the technical status at the time of printing.

Basetech 350C12 - 1586224 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info